manualshive.com logo in svg

Weishaupt WTC-GB 15-B Compact, Инструкция по установке и эксплуатации

Weishaupt WTC-GB 15-B Compact - Компактный газовый котел с инструкцией по монтажу и эксплуатации. Можно скачать бесплатно на manualshive.com для получения руководства пользователя. Удобное решение для вашего дома.

Поделиться
Скачать
background image

Installation and operating instruction
Gas condensing unit WTC-GB 15-B Compact and WTC-GB 25-B Compact

9 Servicing

83309302 1/2018-05 La

120-196

9 Servicing

9.1 Condensing unit service

9.1.1 Notes on servicing

DANGER

Risk of explosion due to leaking gas

Improper service work can lead to escaping gas and explosion.

Close fuel shut off devices prior to starting work.
Care should be taken when dismantling and assembling gas carrying compon-
ents.
Close the screws on the test points ensuring the tests points are sealed.

DANGER

Risk of electric shock

Working on the device when voltage is applied can lead to electric shock.

Isolate the device from the power supply prior to starting any work.
Safeguard against accidental restart.

DANGER

Danger of poisoning by escaping flue gas

Flue gas can escape if the siphon is not filled. Inhalation leads to dizziness, nausea
and eventually death.

Check the fill level of the siphon at regular intervals and replenish if necessary, in
particular when the system has been shut down for longer periods or has been
operated at high return temperatures > 55 °C.

WARNING

Electric shock despite disconnection from the voltage supply

It is possible that electrical components continue to carry voltage and cause elec-
tric shock even after the voltage supply has been disconnected.

Wait approx. 5 minutes before commencing work.
Electric voltage has dissipated.

WARNING

Danger of getting burned on hot components

Hot components can lead to burns.

Allow components to cool.

Servicing must only be carried out by qualified personnel. The combustion plant
should be serviced annually. Depending on site conditions more frequent checks
may be required.

Components, which show increased wear and tear or whose design lifespan is or
will be exceeded prior to the next service should be replaced as a precaution
[ch. 9.1.2].

Weishaupt recommends a service contract is entered into to ensure regular in-
spections.

The following components must only be replaced and must not be repaired:

WEM-FA-G device electronics,
gas combi valve,
safety valve.

Содержание WTC-GB 15-B Compact





































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WTC-GB 15-B Compact

Daikin C-Series Operation Manual preview
C-Series
Бренд: Daikin Страницы: 27
Uberhaus 1820 Owner'S Manual preview
1820
Бренд: Uberhaus Страницы: 19
Daikin Altherma 3 H MT ECH2O Operation Manual preview
Altherma 3 H MT ECH2O
Бренд: Daikin Страницы: 24
Daikin Altherma 3 H MT ECH2O User Reference Manual preview
Altherma 3 H MT ECH2O
Бренд: Daikin Страницы: 68
Daikin 2MXU40GV1B Service Manual Removal Procedure preview
2MXU40GV1B
Бренд: Daikin Страницы: 46
Daikin ALTHERMA User Reference Manual preview
ALTHERMA
Бренд: Daikin Страницы: 24
E-one Sewers 1000 Series User Instructions preview
Sewers 1000 Series
Бренд: E-one Страницы: 3
E-one Extreme Series Typical Installation Instructions & Warranty Information preview
Extreme Series
Бренд: E-one Страницы: 23
E-one Extreme Series Service Manual preview
Extreme Series
Бренд: E-one Страницы: 76
valent VRC Series Installation, Operation & Maintenance Instructions Manual preview
VRC Series
Бренд: valent Страницы: 20
Dakota Digital Odyssey ODYR-25-1 Manual preview
Odyssey ODYR-25-1
Бренд: Dakota Digital Страницы: 8
Bionaire BOF3001-CN Instruction Leaflet preview
BOF3001-CN
Бренд: Bionaire Страницы: 8
Haverland New XR Designer Instruction Manual preview
New XR Designer
Бренд: Haverland Страницы: 8
Purmo RADSON MIED0508EL Installation & Maintenance preview
RADSON MIED0508EL
Бренд: Purmo Страницы: 32
CALEFFI SATK20 Series Instructions For Installation, Commissioning And Maintenance preview
SATK20 Series
Бренд: CALEFFI Страницы: 16
L.B. White AW250 Owner'S Manual And Instructions preview
AW250
Бренд: L.B. White Страницы: 30
Rosenbauer DIGIDOS24 AT Operation Manual preview
DIGIDOS24 AT
Бренд: Rosenbauer Страницы: 27
Xylem LSP0311A Instruction Manual preview
LSP0311A
Бренд: Xylem Страницы: 20

Бренды по названию

Популярные бренды

Загрузить еще бренды