Weishaupt WTC-GB 15-B Compact Скачать руководство пользователя страница 80 | Manualshive

Страница: 80 / 196

background image

Installation and operating instruction
Gas condensing unit WTC-GB 15-B Compact and WTC-GB 25-B Compact

6 Operation

83309302 1/2018-05 La

80-196

6.6.5.2 Control behaviour

Heating
circuits

Control
behaviour

Parameters

Setting

6.2.1
Heat-up optimisation

To ensure that the room setpoint temperature reaches the level set at the begin-
ning of the heating program, the switch-on time for the start of the heating is ad-
vanced.

Off

:

Heat-up optimisation not activated.

On

:

Heat-up optimisation activated.

6.2.2
Heat-up optimisation
Maximum advance

(1

Limits the maximum time of advancement for heat optimisation.

6.2.3
Building construction

With weather compensated control the mixed external temperature influences the
flow setpoint temperature. The influence depends on the building construction.
The better (heavier) the building construction, the slower the influence.

very light

…

very heavy

6.2.4
Room thermostat func-
tion

(1

The room thermostat switches off the heating circuit, when the room temperature
exceeds the

room setpoint temperature

+ switch differential.

Off

:

Room thermostat function not activated.

On

:

Room thermostat function activated.

On at setback

:

The room thermostat function is only activated at level

setback

.

Switch differential:
If the current room temperature exceeds the room setpoint temperature by the
switch differential, the heating circuit is switched off.

6.2.5
Room sensor influence

With room compensated control, the difference between the current room temper-
ature and the room setpoint temperature set influences the flow temperature. The
higher the value of the room sensor influence set, the more affect the difference
will have.

6.2.6
Room control I-Part

With active PI room control, an exact compensation of the room setpoint temperat-
ure is achieved.

On

:

PI room control activated.

Off

:

On:PI room control not activated.

Reset time:
The shorter the reset time, the faster a control deviation is compensated. If the time
is set too short, the controller tends to oscillate.

6.2.7
Frost protection
External temperature

If the current external temperature drops below the value set, system frost protec-
tion is activated.

(1

Factory setting depending on the heating circuit type set [ch. 12.7].

«
...
78
79
80
81
82
...
»

Содержание WTC-GB 15-B Compact





































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WTC-GB 15-B Compact

Бренд: Lasko Страницы: 4

Бренд: Dantherm Страницы: 12

Бренд: Orava Страницы: 19

Бренд: Bard Страницы: 24

Бренд: Panduit Страницы: 7

Бренд: Texas Equipment Страницы: 11

Бренд: ICP Страницы: 13

Бренд: IMO Страницы: 11

AquaMax Eco Premium

Бренд: Oase Страницы: 380

Master BLP 17M DC

Бренд: MCS Страницы: 41

Бренд: SAMES KREMLIN Страницы: 50

Бренд: Nortek Страницы: 16

Бренд: YAMADA Страницы: 22

Бренд: EUROM Страницы: 80

KH 4256 AIR PUMP

Бренд: ULTIMATE SPEED Страницы: 72

Бренд: Carrier Страницы: 16

Бренд: NewAir Страницы: 12

Бренд: SuperFish Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды