manualshive.com logo in svg

Weishaupt WTC-GB 15-B Compact, Инструкция по установке и эксплуатации

Weishaupt WTC-GB 15-B Compact - Компактный газовый котел с инструкцией по монтажу и эксплуатации. Можно скачать бесплатно на manualshive.com для получения руководства пользователя. Удобное решение для вашего дома.

Поделиться
Скачать
background image

Installation and operating instruction
Gas condensing unit WTC-GB 15-B Compact and WTC-GB 25-B Compact

6 Operation

83309302 1/2018-05 La

63-196

6.5.6 Settings

Settings

Parameters Setting

Time of day

Set current time of day.

Date

Set current date.

Summertime

Configure automatic change-over of summertime.

On

 (factory setting)

Off

WEM Portal

activate acces to WEM Portal [ch. 12.11].

The following information is required for access and is displayed here:

Serial number
Access code

Light strip

Deactivate light strip on condensing unit.

On

 (factory setting):

Light strip activated.

Off

:

Light strip deactivated.

Sensor
correction

External sensor

Correction of the current outside temperature (factory setting:

 0.0 K

)

If no optimal placement of the outdoor sensor is possible or a measurement error is to be com-
pensated, the measured outdoor temperature can be corrected.

Room sensor

Correction of the current room temperature (factory setting:

 0.0 K

).

If no optimal placement of the room sensor is possible or a measurement error is to be compensated,
the measured room temperature can be corrected.

Содержание WTC-GB 15-B Compact





































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WTC-GB 15-B Compact

Accorroni S Series Operation And Installation Manual preview
S Series
Бренд: Accorroni Страницы: 40
Jandy JCP Series Installation And Operation Manual preview
JCP Series
Бренд: Jandy Страницы: 108
Jandy Pro Series JXi 200 Installation Instructions Manual preview
JXi 200
Бренд: Jandy Pro Series Страницы: 40
TATRA PC-10 Installation And Operation Manual preview
PC-10
Бренд: TATRA Страницы: 16
Daikin KEH067A41E(A) Installation Instructions Manual preview
KEH067A41E(A)
Бренд: Daikin Страницы: 12
KSB Delta Solo Compact MVP Series Installation & Operating Manual preview
Delta Solo Compact MVP Series
Бренд: KSB Страницы: 40
Cadet Hot One Owner'S Manual preview
Hot One
Бренд: Cadet Страницы: 9
Raider RD-EFH02 User Manual preview
RD-EFH02
Бренд: Raider Страницы: 54
HeatStar HSRR30SP(LP) Operating Instructions And Owner'S Manual preview
HSRR30SP(LP)
Бренд: HeatStar Страницы: 32
Dupla MARIN P4 Smart Operating Instruction preview
P4 Smart
Бренд: Dupla MARIN Страницы: 28
Ingersoll-Rand ARO PP10A Series Operator'S Manual preview
ARO PP10A Series
Бренд: Ingersoll-Rand Страницы: 12
Warren rupp Sandpiper S05 Service & Operating Manual preview
Sandpiper S05
Бренд: Warren rupp Страницы: 22
BLACKMER LGL154A Installation, Operation And Maintenance Instructions preview
LGL154A
Бренд: BLACKMER Страницы: 12
Watson-Marlow 501RLA User Manual preview
501RLA
Бренд: Watson-Marlow Страницы: 576
KSB BPD 242 Operating Instructions Manual preview
BPD 242
Бренд: KSB Страницы: 20
Wacker Neuson PG2A Operator'S Manual preview
PG2A
Бренд: Wacker Neuson Страницы: 60
habitat et jardin VP2012 Instruction Manual preview
VP2012
Бренд: habitat et jardin Страницы: 19
Tripp Lite WEXT5-SRCOOL12K Quick Manual preview
WEXT5-SRCOOL12K
Бренд: Tripp Lite Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды