Weishaupt WTC-GB 15-B Compact Скачать руководство пользователя страница 164

Страница: 164 / 196

Installation and operating instruction
Gas condensing unit WTC-GB 15-B Compact and WTC-GB 25-B Compact

12 Technical documentation

83309302 1/2018-05 La

164-196

12.11 Remote access to heating system via internet

Remote access to the heating system via the Internet is possible via web browser
or app.

For remote access, the WEM portal must first be set up.

Network configuration

The device is set for automatic network configuration.

Depending on the network, switching to manual network configuration may be re-
quired.

Access data for manual network configuration:

Network address:

http://wem-sg

User name: admin
Password: Admin123

Connect network cable

Connect the router to the Ethernet socket on the display and operating unit (sys-
tem unit).

Activate the WEM portal on the condensing unit

Select user level [ch. 6.5].
Select

Settings

and confirm.

Select

WEM-Portal

and confirm.

Select rectangle for

Portal access

using the dial knob and confirm.

Colour of rectangle change to green.
A new

Access code

is being generated.

Access to the WEM-Portal is activated.
Note down the

Serial Number

and

Access code

Registering

Access address

https://www.wemportal.com/

via the web browser.

Click on

Carry out registration.

System > Overview

is displayed.

Set up the heating system in the WEM portal

Click on

Set up system

Assign

System name

(freely selectable).

Enter noted down

Serial Number

and

Access code

Enter

Registration code

from Weishaupt voucher.

Click on

Setup

The system is set up.

Install the App (optional)

Install the App "Weishaupt Energy Manager" on the end device.

Содержание WTC-GB 15-B Compact





































































































































































































Результаты поиска

Содержание WTC-GB 15-B Compact

Отзывы:

Похожие инструкции для WTC-GB 15-B Compact

Бренды по названию

Популярные бренды

Weishaupt WTC-GB 15-B Compact, Инструкция по установке и эксплуатации

Результаты поиска

Содержание WTC-GB 15-B Compact

Отзывы:

Похожие инструкции для WTC-GB 15-B Compact

Бренды по названию

Популярные бренды