WaterLogic WL Cube Скачать руководство пользователя страница 8

Страница: 8 / 76

OPERATING INSTRUCTIONS

The above picture shows front LCD display and control panel for the

Waterlogic CUBE

Button

Operational Use

Select Cold Water Sel Dispensing Button to start dispensing until

desired fill.

Select Ambient Water Sel Dispensing Button to start dispensing

until desired fill.

Hold for 3 seconds

Press and Hold Hot Water Selection for 3 seconds, until the Hot Water

Icon is illuminated. Press dispensing button until desired fill.

The delay is

a safety feature that prevents hot water from being accidently dispensed.

Hold until Extra Hot Selection

button stops flashing –

indicates the temperature has

been reached..

Press and Hold Extra Hot Water Selection. The Extra Hot Selection

Button will flash red to indicate the water is heating. When the red

flashing icon turns off, this indicates that the water is to the

temperature.

Press the Hot Water Selection the Dispensing button until

desired fill.

WARNING!

Unit produces Very Hot Water up to 203°F. Water above

125°F can cause severe burns or scalding. Keep unauthorized people

and children away from the unit to avoid accidental dispensing of hot

water. Children should not use without supervision.

CUBE

Operating, Installation, and Service Manual

Page 8 - Revision: 6-23-2015

Содержание WL Cube













































































Результаты поиска

Содержание WL Cube

Отзывы:

Похожие инструкции для WL Cube

Бренды по названию

Популярные бренды

WaterLogic WL Cube, Руководство по эксплуатации, установке и обслуживанию

Результаты поиска

Содержание WL Cube

Отзывы:

Похожие инструкции для WL Cube

Бренды по названию

Популярные бренды