WaterLogic WL Cube Скачать руководство пользователя страница 28

Страница: 28 / 76

HOT TANK ENABLING PROCEDURE

During Initial Installation or anytime the unit loses power, you must follow the Hot Tank Enabling

Procedure.

Plug in power cord to 15 amp 120VAC / 60Hz supply (GFCI recommended).

Turn the Red Power Switch on back of Cube. I=ON

Ensure green heater / compression switch is in the O=OFF.

Press the Hot Select Icon for 2 seconds until it illuminates.

Press the dispense button continuously for a minimum of 10 seconds. The dispense backlight will

turn Red indicating Hot Water.

Always continue to dispense until water comes out the faucet to ensure the hot tank is full before

turning on the heater circuit.

Turn on the Green Heater/Compression switch. Green switch into

the (I) position and the switch illuminates.

This ensures the Hot Water is full of water before the Heat Circuit will

enable.

CAUTION!

NEVER TURN ON HEATER BEFORE FILLING HOT TANK.

Green Compressor/Heater Switch must be in the O=OFF position while the hot tank is empty.

Damage could occur within one minute and the overload (high limit) will require manual reset if

heater is turned on with an empty hot tank.

CUBE

Operating, Installation, and Service Manual

Page 28 - Revision: 6-23-2015

Содержание WL Cube













































































Результаты поиска

Содержание WL Cube

Отзывы:

Похожие инструкции для WL Cube

Бренды по названию

Популярные бренды

WaterLogic WL Cube, Руководство по эксплуатации, установке и обслуживанию

Результаты поиска

Содержание WL Cube

Отзывы:

Похожие инструкции для WL Cube

Бренды по названию

Популярные бренды