VST GREEN MACHINE VST-GM-CS2-101 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 219

background image

4.5 - GREEN MACHINE

™

- North America - Installation, Operation, Maintenance, & Troubleshooting Manual

Chapter 1: GREEN MACHINE

™

Installation Instructions

Page 34

Snapshot of Site Requirements, continued…

Roof Top Installation Requirements

•

The GREEN MACHINE

may be installed on a station’s roof provided the structure can

support the weight of the GREEN MACHINE.

•

Due to a variety of roof construction designs, VST cannot recommend how the GREEN
MACHINE should be mounted on the roof; however, the GREEN MACHINE must be
installed at a height allowing the piping inlet and outlets to be above or through the
building parapet.

•

All safety and code concerns must be taken into consideration prior to a roof-top
installation.

•

The GREEN MACHINE has

24”

legs that can be bolted on the base, but the legs may be

removed and the GREEN MACHINE secured to a steel structure attached to the roof.

•

A new air outlet vent riser connected to the GREEN MACHINE must be installed to release
air to the atmosphere.

•

A Design Engineer is responsible for designing the support structure, support base, all
required hardware and bolting connections, and the support structure foundation to meet
all regulatory specifications that may be required by local jurisdictions.

Canopy Top Installation Requirements

•

The GREEN MACHINE

may be installed on a station’s canopy provided the structure can

support the weight of the GREEN MACHINE.

•

Due to a variety of canopy construction designs, VST cannot recommend how the GREEN
MACHINE

should be mounted on the canopy.

•

All safety and code concerns must be taken into consideration prior to a canopy top
installation.

•

The GREEN MACHINE has

24”

legs that can be bolted on the base, but the legs may be

removed and the GREEN MACHINE secured to a steel structure attached to the canopy
support structure.

•

A new air outlet vent riser connected to the GREEN MACHINE

must be installed to release

air to the atmosphere.

•

A Design Engineer is responsible for designing the support structure, support base, all
required hardware and bolting connections, and the support structure foundation to meet
all regulatory specifications that may be required by local jurisdictions.

«
...
32
33
34
35
36
...
»

Содержание GREEN MACHINE VST-GM-CS2-101




























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GREEN MACHINE VST-GM-CS2-101

PURE FLOATING BRIDGE

Бренд: K&K Sound Страницы: 2

Бренд: SAelen TS Страницы: 44

Бренд: Philips Страницы: 3

Бренд: Philips Страницы: 3

Бренд: Philips Страницы: 3

Бренд: DataCard Страницы: 1

Бренд: TAGG Страницы: 2

Library L100 Reader

Бренд: TAGSYS Страницы: 45

Turboflotor 5000 Baby Turboflotor 5000 Twin

Бренд: Aqua Medic Страницы: 35

Бренд: VIGO Страницы: 15

Бренд: Kruger&Matz Страницы: 40

Djangobucker 2018

Бренд: Krivo Pick-ups Страницы: 3

Бренд: LaBina Страницы: 9

Бренд: Barska Страницы: 2

Бренд: Xytronix Research & Design Страницы: 54

Invisible Reader

Бренд: Cansec Страницы: 4

Radial Winch 80.3 ST

Бренд: Harken Страницы: 19

AYERS ROCK DI 100P

Бренд: Gecko Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды