Volvo TAD420VE Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 62

background image

Maintenance

32

Battery. Maintenance

WARNING!

Fire and explosion hazard. Batter-

ies must never be exposed to open flames or
sparks.

WARNING!

Never confuse the positive and

negative poles on the batteries. Risk of arcing
and explosion.

WARNING!

Battery electrolyte is highly corro-

sive. Always protect your eyes, skin and clothes
when handling batteries. Always use protective
goggles and gloves. If acid comes into contact
with your skin, wash at once with soap and a
lot of water. If you get battery acid in your eyes,
flush at once with a lot of water, and get medical
assistance at once.

Connection and disconnection

When you connect batteries, first connect the + cable
(red) to the + pole on the battery. Then connect the -
cable (black) to the - pole on the battery

When you disconnect batteries, connect the - cable
(black) first, then the + cable (red).

Cleaning

Keep the batteries dry and clean. Contamination and
oxide on the batteries and battery poles can cause
stray currents, voltage drop and discharge, especially
in wet weather. Clean oxidation from the battery
poles and terminals, using a copper brush. Tighten
the terminals securely and grease them with terminal
grease or Vaseline.

Filling

The electrolyte level should be 5-10 mm (0.2-0.4”)
above the cell plates in the battery. Top up with

dis-

tilled water

as necessary. After filling, the battery

should be charged for at least 30 minutes by running
the engine at fast idle. NOTE! Some maintenance-
free batteries have special instructions, which must
be observed.

«
...
32
33
34
35
36
...
»

Содержание TAD420VE































































Отзывы:

Нет отзывов

Похожие инструкции для TAD420VE

Бренд: Saito Страницы: 2

Бренд: Graco Страницы: 26

EM-PMI540-T4000

Бренд: Danfoss Страницы: 71

Бренд: JetCat Страницы: 54

Бренд: CW Products Страницы: 4

Бренд: Tahmazo Страницы: 3

Бренд: WEN POWER Страницы: 28

Бренд: Kyosho Страницы: 4

Бренд: FAAC Страницы: 88

Бренд: Lin Engineering Страницы: 23

Бренд: DAYE Страницы: 80

Бренд: Man Страницы: 6

Бренд: Geckodrive Страницы: 8

Бренд: SABB MOTOR Страницы: 54

Бренд: Sears Страницы: 12

Бренд: O.S. engine Страницы: 4

Бренд: Danfoss Страницы: 36

Бренд: Leroy-Somer Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды