Volvo TAD420VE Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 62

background image

Starting the engine

15

Never use start spray

WARNING!

Never use start spray or similar

products as a starting aid. Explosions could oc-
cur in the inlet manifold. The consequence could
be personal injury.

Starting with auxiliary batteries

WARNING!

Batteries (especially auxiliary bat-

teries) contain hydrogen which is highly explo-
sive in contact with air. A spark, which can be
formed if the auxiliary batteries are wrongly
connected, is enough to make a battery explode
and cause damage.

1. Check that the auxiliary batteries are connected

(series or parallel) so that the rated voltage cor-
responds to the engine system voltage.

2. First connect the red (+) jumper cable to the

auxiliary battery, then to the flat battery. Then
connect the black jumper cable (–)

to the auxil-

iary battery, and lastly to a place

some distance

from the flat batteries

, such as the negative

cable by the main switch or the negative cable
connection on the starter motor.

3. Start the engine.

WARNING!

Do not move the connections when

you attempt to start the engine (risk of arcing),
and do not stand and lean over one of the bat-
teries.

4. Remove the jumper cables in the reverse order

from installation.

WARNING!

The ordinary cables to the standard

batteries must not be loosened on any condi-
tion.

«
...
15
16
17
18
19
...
»

Содержание TAD420VE































































Отзывы:

Нет отзывов

Похожие инструкции для TAD420VE

Бренд: Rail King Страницы: 46

Бренд: ULPOWER Страницы: 20

Бренд: Avco Lycoming Страницы: 110

Calzoni MR Series

Бренд: Parker Страницы: 50

Бренд: Kober Страницы: 112

AG2210-LP Series

Бренд: Beckhoff Страницы: 35

Throttling Governor Kerosene Stationary Engines

Бренд: Worthington Страницы: 33

Бренд: Volvo Penta Страницы: 100

Бренд: Volvo Penta Страницы: 104

Бренд: Metronic Страницы: 28

Бренд: KEM Страницы: 61

Бренд: ZIEHL-ABEGG Страницы: 12

Бренд: ZIEHL-ABEGG Страницы: 20

Бренд: Spectrum Страницы: 327

Бренд: KTM Страницы: 159

Бренд: Ford Страницы: 6

Бренд: Mitsubishi Страницы: 16

Бренд: Seidel Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды