Volvo TAD420VE Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 62

background image

31

Maintenance

WARNING!

Before any work is done on the electrical system, the engine must be stopped and the current

cut by switching off the main switch. Battery chargers or other auxiliary equipment installed on the engine
must be disconnected.

Electrical system

Fuses

No fuses or circuit breakers are supplied with the en-
gine. Customers have to install the electrical system
on the side of the vehicle themselves.

Fuses cut the current if the electrical system is over-
loaded.

If the engine can not be started, or if the instrument
stop working during operation, a fuse or circuit break-
er can have tripped. Check and replace fuses or re-
set circuit breakers.

IMPORTANT!

Always investigate the reason for

the overload!

Main switch

The main switch must never be disconnected before
the engine has been stopped. If the circuit between
the alternator and the battery is disconnected when
the engine is running, the alternator can be dam-
aged.

IMPORTANT!

Never disconnect the current with

the main switch when the engine is running.

Electrical connections

Check that electrical connections are dry, free from
oxide and that they are securely tightened. Spray
these connections as necessary with water-repellent
spray (Volvo Penta universal oil).

«
...
31
32
33
34
35
...
»

Содержание TAD420VE































































Отзывы:

Нет отзывов

Похожие инструкции для TAD420VE

Бренд: Daihatsu Страницы: 294

Viper Engines 31321

Бренд: Ardisam Страницы: 20

Бренд: Nanni Страницы: 13

Бренд: Perkins Страницы: 88

Бренд: GAPOSA Страницы: 2

Бренд: Briggs & Stratton Страницы: 12

Бренд: Applied Motion Products Страницы: 2

Бренд: GR Страницы: 8

Бренд: Superrollo Страницы: 68

Бренд: SSANGYONG Страницы: 14

CYQD 32 Series CYQD32

Бренд: Dongfeng Chaoyang Diesel engine Co Страницы: 60

Бренд: CAME Страницы: 96

Бренд: Baotian Страницы: 41

Бренд: RIEJU Страницы: 63

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

Бренд: Grundfos Страницы: 12

Nitro Star T-15

Бренд: HPI Racing Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды