Volvo TAD420VE Скачать руководство пользователя страница 43

Страница: 43 / 62

Fault codes

PID 174, Code 2.3.7 Warning, fuel temperature

Reason:

Excessive fuel temperature.

Reaction:

A fault code is generated. The fault code

disappears when the fuel temperature falls below the

recuperation value.

Action:

• Check the fuel.

• Check the sensor cable for breaks and short cir-

cuits.

• Check sensor function. Change the sensor as

necessary.

PID 100, Code 2.3.1 Emergency stop, oil
pressure

Reason:

Oil pressure below specified limit value.

Reaction:

Engine is emergency stopped.

Action:

• Check the oil level and oil pump.

• Check the sensor cable for breaks and short cir-

cuits.

• Check sensor function. Change the sensor as

necessary.

• Check the limit value for engine shut-off due to oil

pressure.

PID 110, Code 2.3.2 Emergency stop, coolant
temperature

Reason:

Excessive coolant temperature

Reaction:

Engine is emergency stopped.

Action:

• Check the coolant.

• Check the sensor cable for breaks and short cir-

cuits.

• Check sensor function. Change the sensor as

necessary.

• Check the limit value for engine shut-off due to

coolant pressure.

PID 111, Code 2.3.5 Warning, coolant level

Reason:

Coolant level too low

Reaction:

A fault code is generated.

Action:

• Check the coolant level.

• Check the sensor cable for breaks and short cir-

cuits.

• Check sensor function (if installed).

Change the sensor as necessary.

NOTE! The engine is supplied without a coolant level
sensor.

PID 190, Code 2.3.6 Overspeed in limp home
mode

Reason:

When the limp home mode is activated and

the engine speed is or has been higher than the per-

missible limit value.

Reaction:

GE: Engine is shut off. A fault code is gen-

erated.
VE: Fuel injection ceases when the control rod re-

turns to its home position and the fault code lamp

lights up until the engine speed falls below the per-

missible limit again.

Action:

• Check the control rod for the injection pumps.

• Check the actuator, replace it if necessary.

• Check the cables for the actuator for breaks and

short circuits.

• Check the number of teeth on the camshaft

wheel.

• For VE engines, it may be necessary to check the

function of the “limp home” mode

Содержание TAD420VE































































Результаты поиска

Содержание TAD420VE

Отзывы:

Похожие инструкции для TAD420VE

Бренды по названию

Популярные бренды

Volvo TAD420VE, Руководство оператора

Результаты поиска

Содержание TAD420VE

Отзывы:

Похожие инструкции для TAD420VE

Бренды по названию

Популярные бренды