Volvo TAD420VE Скачать руководство пользователя страница 41

Страница: 41 / 62

Fault codes

PID 91, Code 2.2.1 Accelerator pedal sensor

Reason:

Faulty sensor, connector or cable.

Reaction:

The engine goes into “limp home” mode.

Action:

• Check the sensor cable for breaks and short cir-

cuits.

• Check sensor function. Change the sensor as

necessary.

WARNING!

Read through the safety advice for care and maintenance work in the “Safety information”

chapter before starting work.

Code 2.0.0

No faul

There are no active faults.

PID 190, Code 2.1.1 Engine speed sensor,
camshaft

Reason:

Faulty sensor, connector, cables or incor-

rect distance to cam wheel. High frequency interfer-

ence.

Reaction:

Engine is shut off.

Action:

• Check that the engine speed sensor is installed

with the correct distance to the camshaft.

• Check the cables for the engine speed sensor for

breaks and short circuits.

• Check the connector for poor contact.

• Check engine speed sensor function. Change the

sensor as necessary.

PID 190, Code 2.1.4 Overspeed

Reason:

The engine speed is or has been higher

than the permissible limit.

Reaction:

Fuel injection ceases and the fault code

lamp lights up until the engine speed falls below the

permissible limit again.

Action:

• Check the control rod for the injection pumps.

• Check the actuator, replace it if necessary.

• Check the cables for the actuator for breaks and

short circuits.

• Check the number of teeth on the camshaft

wheel.

• For VE engines, it may be necessary to check the

function of the “limp home” mode

Содержание TAD420VE































































Результаты поиска

Содержание TAD420VE

Отзывы:

Похожие инструкции для TAD420VE

Бренды по названию

Популярные бренды

Volvo TAD420VE, Руководство оператора

Результаты поиска

Содержание TAD420VE

Отзывы:

Похожие инструкции для TAD420VE

Бренды по названию

Популярные бренды