Volvo TAD420VE Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 62

background image

Starting the engine

14

Starting in extreme cold

Certain preparations must be made to facilitate en-
gine starting, and in some cases to make starting
possible at all.

Use a winter grade fuel (of a well-known make) which
has been approved for the relevant temperature. This
reduces the risk of wax deposits in the fuel system.
At extremely low temperatures, the use of a fuel heat-
er is recommended.

For fully acceptable lubrication, a synthetic engine
oil of recommended viscosity for the relevant tem-
perature should be used. Please refer to the “Main-
tenance, lubrication system” chapter: Synthetic lubri-
cants are able to manage a wider temperature range
than mineral-based lubricants.

Pre-heat the coolant with a separately installed elec-
tric engine heater. In extreme cases, a diesel-burning
engine heater may be needed. Ask your Volvo Penta
dealer for advice.

IMPORTANT!

Make sure that the cooling sys-

tem is filled with a glycol mixture. Please refer to
the “Maintenance, cooling system” chapter:

The batteries should be in good condition. Cold
weather reduced battery capacity. Increased battery
capacity may be necessary.

«
...
14
15
16
17
18
...
»

Содержание TAD420VE































































Отзывы:

Нет отзывов

Похожие инструкции для TAD420VE

Бренд: O.S. engine Страницы: 32

Бренд: Schartec Страницы: 16

Бренд: Tanaka Страницы: 10

Бренд: HAIMA Страницы: 10

Бренд: LCT Страницы: 25

HYDRO-FORCE 65043

Бренд: Bestway Страницы: 8

Бренд: Volvo Penta Страницы: 96

Бренд: Volvo Penta Страницы: 106

Бренд: O.S. engine Страницы: 16

Бренд: O.S. engine Страницы: 46

Бренд: O.S. engine Страницы: 38

Бренд: Baumuller Страницы: 25

Бренд: Motion Страницы: 52

Бренд: Ingersoll-Rand Страницы: 4

Бренд: FAAC Страницы: 20

Бренд: A.O. Smith Страницы: 52

Бренд: YARDMAX Страницы: 28

Parilla LEOPARD

Бренд: IAME Страницы: 46

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды