Volvo TAD420VE Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 62

background image

2

Safety information

Incorrect operation can lead to personal injury and damage to products or property. So read
the instruction book through very carefully before you start the engine or do any maintenance
or service work. If there is still something which is unclear or if you feel unsure about it, please
contact your Volvo Penta dealer for assistance.

This symbol is used in the instruction book and on the product, to call your attention to the

fact that this is safety information. Always read such information very carefully.

Safety texts in the instruction book have the following order of priority:

WARNING!

Warns for the risk of personal injury, major damage to product or property, or

serious malfunctions if the instruction is ignored.

IMPORTANT!

Is used to call attention to things which could cause damage or malfunctions

to product or property.

NOTE!

Is used to call attention to important information, to facilitate work processes or opera-

tion.

This symbol is used on our products in some cases and refers to important information in
the instruction book. Make sure that warning and information symbols on the engine are clearly
visible and legible. Replace symbols which have been damaged or painted over.

Read this chapter very carefully. It has to do with your safety. This describes how safety information is presented
in the instruction book and on the product. It also gives you an introduction to the basic safety rules for using and
looking after the engine.

Check that you heave received the correct instruction book before you read on. If not, please contact
your Volvo Penta dealer.

«
...
2
3
4
5
6
...
»

Содержание TAD420VE































































Отзывы:

Нет отзывов

Похожие инструкции для TAD420VE

Бренд: O.S. engine Страницы: 19

Бренд: EuroLite Страницы: 19

T-MODE TM 45 R 15/17

Бренд: FAAC Страницы: 10

Бренд: Doosan Страницы: 350

Бренд: WÄRTSILÄ Страницы: 522

Бренд: KSB Страницы: 52

Бренд: Perkins Страницы: 42

Бренд: Newland Страницы: 29

Бренд: Eastwood Страницы: 20

Бренд: INDUSTRIAS TECHNOFLEX Страницы: 40

Бренд: Yanmar Страницы: 164

Бренд: Electro motive Страницы: 287

Бренд: Chicago Pneumatic Страницы: 100

Бренд: Detroit Diesel Страницы: 116

Бренд: Detroit Diesel Страницы: 158

Бренд: Detroit Diesel Страницы: 172

Бренд: Powertrain Страницы: 36

Бренд: KRESS Страницы: 46

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды