Volvo TAD420VE Скачать руководство пользователя страница 38

Страница: 38 / 62

Fault tracing

A number of symptoms and possible causes of engine malfunctions are described in the table below. Always
contact your Volvo Penta dealer if any problems occur which you can not solve by yourself.

WARNING!

Read through the safety advice for care and maintenance work in the “Safety information”

chapter before starting work.

The diagnosis button lamp flashes.

Please refer to the “Diagnostic information” chapter.

Engine can not be stopped.

2, 4

Starter motor does not rotate

1, 2, 3, 4, 5, 6, 7, 24

Starter motor rotates slowly

1, 2

Starter motor rotates normally but engine does not start

8, 9, 10, 11

Engine starts but stops again

8, 9, 10, 11, 13

Engine does not reach correct operating speed at full throttle 9, 10, 11, 12, 13, 21, 25, 26

Engine runs roughly

10, 11, 27

High fuel consumption

12, 13, 15, 25

Black exhaust smoke

12, 13

Blue or white exhaust smoke

14, 15, 22

Too low lubrication oil pressure

Excessive coolant temperature

17, 18, 19, 20

Too low coolant temperature

No, or poor charge

2, 23

1. Flat batteries

2. Poor contact/open circuit in

cables

3. Main switch turned off

4. Faulty ignition lock

5. Faulty main relay

6. Faulty starter motor relay

7. Faulty starter motor/solenoid

8. Lack of fuel:

– fuel taps closed

– fuel tank empty/wrong tank

connected

9. Blocked fuel filter/pre-filter

(because of contamination, or
paraffin fraction separation in
fuel at low temperature).

10. Air in the fuel system

11. Water/contamination in fuel

12. Faulty injection pumps

13. Insufficient air supply to en-

gine:

– blocked air filter

– air leakage between turbo-

charger and engine inlet pipe.

– fouled compressor section in

turbocharger

– faulty turbocharger

– poor engine bay ventilation

14. Excessive coolant temperature

15. Too low coolant temperature

16. Too low oil level

17. Coolant level too low

Symptoms and possible causes

18. Air in the coolant system

19. Faulty circulation pump

20. Defective thermostat

21. Blocked intercooler

22. Too high oil level

23. Alternator drive belt slips

24. Water entry into engine

25. High back pressure in exhaust

system

26. Break in “Pot+” cable to pedal

27. Incorrectly set engine speed

regulator / actuator

Содержание TAD420VE































































Результаты поиска

Содержание TAD420VE

Отзывы:

Похожие инструкции для TAD420VE

Бренды по названию

Популярные бренды

Volvo TAD420VE, Руководство оператора

Результаты поиска

Содержание TAD420VE

Отзывы:

Похожие инструкции для TAD420VE

Бренды по названию

Популярные бренды