Volvo TAD420VE Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 62

background image

Maintenance

26

Coolant. Checking and filling

WARNING!

Do not open the filler cap when the

engine is warm, except in emergencies. Steam
or hot fluid could spray out.

Check the coolant level daily before starting. Top the
coolant up as necessary. The level should be about
50 mm (2”) below the sealing plane of the filler cap,
or between the MIN and MAX markings, if a separate
expansion tank is installed.

IMPORTANT!

Topping up should be done with

the same type of mixture as is already in the
cooling system.

Filling a completely empty system

Check that all drain points are closed.

The location of drain and vent taps is shown
overleaf.

Filling should be done with the engine stationary. Fill
up slowly, to allow the air to flow out.

If a heating unit is connected to the engine cooling
system, the heat control valve should be opened and
the installation vented during filling.

Fill up with coolant to the correct level.

Do not start

the engine until the system is vented and com-
pletely filled.

Start the engine and warm it up until the thermostats
are fully open (about 20 minutes). Open any venting
taps some while after starting, to allow shut-in air to
escape. Check the coolant level and top up as neces-
sary.

«
...
26
27
28
29
30
...
»

Содержание TAD420VE































































Отзывы:

Нет отзывов

Похожие инструкции для TAD420VE

Бренд: Admiral Страницы: 9

Бренд: jiangdong Страницы: 27

Бренд: Westerbeke Страницы: 140

Бренд: DELTA DORE Страницы: 16

Lombardini LGW 523 MPI

Бренд: Kohler Страницы: 144

Бренд: FPT Страницы: 49

Бренд: Habasit Страницы: 28

Бренд: Haas Страницы: 7

Бренд: Yanmar Страницы: 182

LMG 14000 MONOFASE

Бренд: LOMBARDINI MARINE Страницы: 78

Бренд: DLE Страницы: 4

Бренд: Iveco Страницы: 40

Бренд: Toyan Engine Страницы: 36

Бренд: A'OK Страницы: 7

Бренд: A'OK Страницы: 11

X30 125cc RL - TaG

Бренд: IAME Страницы: 54

Бренд: Jamara Страницы: 2

Бренд: Jamara Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды