Volvo TAD420VE Скачать руководство пользователя страница 44

Страница: 44 / 62

Fault codes

SID 23, Code 2.5.1 Control rod position sensor,
difference

Reason:

Injection pump/actuator has got stuck or is

not connected. Difference between control rod cur-

rent value and nominal value exceeds 10%.

Reaction:

A fault code is generated. The fault code

disappears when the difference between control rod

current value and nominal value falls below 10%.

Action:

• Check the control rod for the injection pumps.

• Check the actuator, control rod and injection

pumps. Change as necessary.

• Check the cables for the actuator for breaks and

short circuits.

SID 23, Code 2.5.2 Injection pump, auto
calibration

Reason:

Automatic actuator equalization is not pos-

sible. Faulty calibration.

Reaction:

The engine is emergency stopped and

can not be re-started until the fault is rectified. The

regulator can not be activated.

Action:

• Check the actuator. Change as necessary.

• Check the actuator cables.

• Turn the ignition off and on, and check if the fault

code remains.

SID 231, Code 2.7.1 Communication fault, CAN
bus

Reason:

CAN controller for CAN bus is faulty.

Reaction:

Action:

• Check the cables.

• Check the control unit.

PID 111, Code 2.3.5 Emergency stop, coolant
level

Reason:

Low coolant level

Reaction:

The engine is emergency stopped and

can not be re-started until the fault is rectified.

Action:

• Check coolant level.

• Check the sensor cable for breaks and short cir-

cuits.

• Check sensor function (if installed).

Change the sensor as necessary.

NOTE! The engine is supplied without a coolant level

sensor.

SID 24, Code 2.5.1 Control rod position sensor

Reason:

Actuator not connected. Faulty value from

control rod position sensor in actuator.

Reaction:

Engine is emergency stopped. Actuator

can not be controlled.

Action:

• Check the actuator. Change as necessary.

• Check the cables for the actuator for breaks and

short circuits.

SID 24, Code 2.5.1 Control rod position sensor,
reference

Reason:

Actuator not connected. Faulty value from

control rod position sensor in actuator.

Reaction:

Engine is emergency stopped. Actuator

can not be controlled.

Action:

• Check the actuator. Change as necessary.

• Check the cables for the actuator for breaks and

short circuits.

Содержание TAD420VE































































Результаты поиска

Содержание TAD420VE

Отзывы:

Похожие инструкции для TAD420VE

Бренды по названию

Популярные бренды

Volvo TAD420VE, Руководство оператора

Результаты поиска

Содержание TAD420VE

Отзывы:

Похожие инструкции для TAD420VE

Бренды по названию

Популярные бренды