Volvo TAD420VE Скачать руководство пользователя страница 25

Страница: 25 / 62

Maintenance

Oil level. Inspection

Make sure that the oil level is between the MAX and
MIN marks.

IMPORTANT!

In continuous operation, the oil

level should be checked every 8 hours.

WARNING!

Working with, or going close to a

running engine is a safety risk. Watch out for ro-
tating components and hot surfaces.

Oil and oil filters. Change

Always follow the recommended oil change interval
and always change the oil filter during oil changes.
On stationary engines, the bottom plug should

not

removed. Use an oil drain pump to suck the oil up.

1. Clean the oil filter holder thoroughly to avoid dirt

entry when the new filter(s) is/are installed.

2. Warm the engine up.

WARNING!

Hot oil and hot surfaces can

cause burns.

3. Remove the bottom plug. Drain the oil.

4. Install the bottom plug with a new gasket.

5. Remove the filer (1). Check that the gasket has

not been left behind on the engine.

5. Fill the new filters with engine oil and wipe oil on

the gaskets. Screw the filters on by hand until the
gaskets just touch the mating surface. Then turn
the filter a further half turn.

Not more!

6. Fill up with oil to the correct level.

Do not fill over

the MAX level.

7. Start the engine and let it idle. Check that the oil

pressure is normal.

8. Stop the engine. Check that no oil leakage occurs

around the filters. Top up with oil as necessary.

Collect the old oil and old filters and hand them
to a re-cycling station for destruction.

Viscosity

Select the viscosity from the table below, for the ap-
propriate continuous ambient air temperature.

* Refers to synthetic or semi-synthetic oils.

Oil change volume

Please refer to the “Technical Data” chapter.

Содержание TAD420VE































































Результаты поиска

Содержание TAD420VE

Отзывы:

Похожие инструкции для TAD420VE

Бренды по названию

Популярные бренды

Volvo TAD420VE, Руководство оператора

Результаты поиска

Содержание TAD420VE

Отзывы:

Похожие инструкции для TAD420VE

Бренды по названию

Популярные бренды