Volvo TAD420VE Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 62

background image

29

Maintenance

Fuel system

Only use the grades of fuel recommended in the fuel specification below. Always observe the greatest cleanli-
ness during re-fueling and work on the fuel system.

All work on the injection system of the engine must be done by an authorized workshop.

If the seal on the in-

jection pump is broken by an unauthorized person, all warranties are void.

WARNING!

Fire hazard. Work on the fuel system must be done with the engine cold. Fuel spills on hot sur-

faces or electrical components can cause fires. Store fuel-soaked rags in a fire-proof manner.

Fuel filter. Change

Cleanliness! No dirt must be allowed to get into the
fuel system.

WARNING!

Fuel filters must be changed when

the engine is cold, to avoid the risk of fire due to
spilled fuel on hot surfaces.

Remove the filters. Wipe a film of oil on the gaskets of
the new filters. Screw the filters on by hand until the
gaskets just touch the mating surface. Then tighten
a further half turn,

no more

. Vent the fuel system.

Hand old filters in to an authorized waste pro-
cessing facility for destruction.

Start the engine and make sure that no leakage oc-
curs.

Fuel specification

The fuel must comply with national and international
standards for commercially supplied fuels, such as:

EN590

(with nationally adapted environmental and

cold requirements)

ASTM-D 975-No 1-D and 2-D.
JIS KK 2204
Sulfur content:

Complying with legal requirements

in each country. If sulfur content exceeds 0.5% by
weight, the

oil change intervals

must be changed,

please refer to the “Lubrication system” heading.

Extremely low sulfur content fuel (urban diesel in
Sweden and city diesel in Finland) can cause a loss
of up to 5% of power and an increase in fuel con-
sumption of about 2–3 %.

«
...
29
30
31
32
33
...
»

Содержание TAD420VE































































Отзывы:

Нет отзывов

Похожие инструкции для TAD420VE

Бренд: Stobag Страницы: 40

Crankcase for Harley-Davidson

Бренд: S&S Cycle Страницы: 12

Бренд: IEF Werner Страницы: 38

Бренд: Jiecang Страницы: 2

7 HP 212 CC OHV

Бренд: Power Fist Страницы: 52

Бренд: Bosch Страницы: 106

rexroth MSK 030

Бренд: Bosch Страницы: 72

Rexroth MKE Series

Бренд: Bosch Страницы: 134

Бренд: Bosch Страницы: 82

Бренд: Bosch Страницы: 124

Rexroth MKE E Series

Бренд: Bosch Страницы: 138

Бренд: Tanaka Страницы: 7

Бренд: FUTABA Страницы: 3

Бренд: Volvo Penta Страницы: 96

Бренд: Volvo Penta Страницы: 106

Бренд: Eastwood Страницы: 20

Бренд: YS Страницы: 5

RolloTube S-line DuoFern

Бренд: RADEMACHER Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды