VKI Technologies Eccellenza Cafe Скачать руководство пользователя страница 68

Страница: 68 / 108

Eccellenza Café – Service Manual

August 5, 2013

Replacing the Bean Grinder Capacitor

With the power to the machine switched off, remove the machine top cover and

then the left side panel.

Remove the brewer assembly.

Remove the milk and hot chocolate powder dispensers.

Remove the powder area wall to gain access to the grinder capacitor.

Using a wrench or socket, remove the large hex nut securing the capacitor to the

wall at the brewer area.

Remove the old capacitor and disconnect the two wires from it.

Connect the two wires to the new capacitor.

Install the capacitor onto the wall and secure it with the large hex nut.

Re-install the powder wall and the two powder dispensers.

10.

Re-install the brewer.

11.

Re-install the left side panel and the top cover.

Содержание Eccellenza Cafe













































































































Результаты поиска

Содержание Eccellenza Cafe

Отзывы:

Похожие инструкции для Eccellenza Cafe

Бренды по названию

Популярные бренды

VKI Technologies Eccellenza Cafe, Руководство по обслуживанию

Результаты поиска

Содержание Eccellenza Cafe

Отзывы:

Похожие инструкции для Eccellenza Cafe

Бренды по названию

Популярные бренды