VKI Technologies Eccellenza Cafe Скачать руководство пользователя

Страница: 62 / 108

Eccellenza Café – Service Manual

August 5, 2013

Disconnect the two power wires from the inlet valve.

At the rear of the machine, remove the two screws securing the inlet valve to

the rear wall of the machine.

Remove the Oetiker clamp securing the tubing assembly to the inlet valve.

The valve can now be completely removed.

Secure the tubing assembly to the new inlet valve with a new Oetiker clamp.

Re-secure the inlet valve assembly to the rear of the machine with two

screws.

Reconnect the power wires to the valve.

10.

Re-install the water tank valve cover.

11.

Re-connect the water supply to the inlet valve.

12.

Switch the machine power on – the water tank will start filling.

13.

Check for leaks.

Содержание Eccellenza Cafe













































































































Результаты поиска

Содержание Eccellenza Cafe

Отзывы:

Похожие инструкции для Eccellenza Cafe

Бренды по названию

Популярные бренды

VKI Technologies Eccellenza Cafe, Руководство по обслуживанию

Результаты поиска

Содержание Eccellenza Cafe

Отзывы:

Похожие инструкции для Eccellenza Cafe

Бренды по названию

Популярные бренды