VKI Technologies Eccellenza Cafe Скачать руководство пользователя

Страница: 107 / 108

Eccellenza Café – Service Manual

August 5, 2013

107

MESSAGE DISPLAYED

CAUSE

POSSIBLE REMEDIES

Printer Error

The printer wiring is not
connected.

•

Connect the wiring to the printer module.

Printer Offline

The printer is connected but
it is offline.

•

Press the ON/OFF line button (power)

on the printer.

SPI Eeprom Error

No communication to the
options board.

•

Check the wiring to the board.

•

Replace the options board.

Tank Not Heating Error

The hot water tank is not
heating.

•

Check the 15 amp fuse.

•

Reset the thermal cut-off switch.

•

Verify wiring to heater element.

•

Check heater element.

Temperature Probe Error

The electronic temperature
probe is not working
properly.

•

Replace the temperature probe.

Verify Powder 1 Level

Powder 1 dispenser is low
and requires refilling.

•

Refill the dispenser for powder 1.

•

Reset the “

Refill

” message for the

Powder 1

dispenser.

Verify Powder 2 Level

Powder 2 dispenser is low
and requires refilling.

•

Refill the dispenser for powder 2.

•

Reset the “

Refill

” message for the

Powder 2

dispenser.

Verify Product Level 1

Coffee 1 dispenser is low
and requires refilling.

•

Refill the dispenser for coffee 1.

•

Reset the “

Refill

” message for the

Coffee 1

dispenser.

Verify Product Level 2

Coffee 2 dispenser is low
and requires refilling.

•

Refill the dispenser for coffee 2.

•

Reset the “

Refill

” message for the

Coffee 2

dispenser.

Verify Waste Bin Level

Waste bin may be full.

•

Empty the contents of the waste bin.

•

Reset the “Waste Bin” counter.

Water Source Error

Indicates a problem with the
main water supply not
getting to the water tank.

•

At this point, the water tank is not full

and this message has to be reset. To reset
it, switch the power off and on.

•

If the problem persists, check all

components on the water line (water filter,
tubing, fittings, etc.).

•

Check inlet valve to make certain it is

functioning properly.

•

In the case of a temporary disruption

with the water supply, the coffee maker will
reset itself after every hour.

Whipper Error

An error has been detected
with the whipper.

•

The whipper motor may be jammed.

Clean the whipper assembly.

•

Verify wiring to the whipper assembly.

•

The whipper motor assembly may need

to be replaced.

Содержание Eccellenza Cafe













































































































Результаты поиска

Содержание Eccellenza Cafe

Отзывы:

Похожие инструкции для Eccellenza Cafe

Бренды по названию

Популярные бренды

VKI Technologies Eccellenza Cafe, Руководство по обслуживанию

Результаты поиска

Содержание Eccellenza Cafe

Отзывы:

Похожие инструкции для Eccellenza Cafe

Бренды по названию

Популярные бренды