VKI Technologies Eccellenza Cafe Скачать руководство пользователя страница 84

Страница: 84 / 108

Eccellenza Café – Service Manual

August 5, 2013

Installing the Coin Changer System

The Eccellenza Café uses the “MDB–Level 3” protocol to communicate with a compatible

coin changer. Although several coin changers are available with this protocol from different

manufacturers, VKI has thoroughly tested and validated ONLY the following coin changer

units for proper operation with the Eccellenza Café:

Coinco

Guardian 6000

™

– a fully customizable 6-tube changer

Coinco

Quantum 700

™

Series – a partially customizable 4-tube changer

It is highly recommended that you acquire the “Operation & Service” manuals for each

of these changers from Coinco

(

www.coinco.com

). These sophisticated changers are highly

customizable and may require direct configuration through their own respective software,

which is totally independent of the Eccellenza Café software configuration.

Install the changer housing skirt and levelers

Remove the coin changer housing from its packaging.

Open the coin changer housing door and remove the housing’s front skirt and two

levelers, which are stored inside.

Install the two levelers onto the bottom of the housing.

Install the skirt onto the bottom front of the housing and secure it in place with the

two screws provided.

Содержание Eccellenza Cafe













































































































Результаты поиска

Содержание Eccellenza Cafe

Отзывы:

Похожие инструкции для Eccellenza Cafe

Бренды по названию

Популярные бренды

VKI Technologies Eccellenza Cafe, Руководство по обслуживанию

Результаты поиска

Содержание Eccellenza Cafe

Отзывы:

Похожие инструкции для Eccellenza Cafe

Бренды по названию

Популярные бренды