VKI Technologies Eccellenza Cafe Скачать руководство пользователя

Страница: 48 / 108

Eccellenza Café – Service Manual

August 5, 2013

Remove the rubber selection button panel from the side of the LCD screen. The panel

is secured to the LCD screen support by an adhesive backing.

Lift a corner of the rubber selection panel until the adhesive peels from the

screen support.

Carefully peel the complete selection button panel from the screen support to

avoid leaving any adhesive behind.

Install the new rubber selection button panel onto the LCD screen support.

Peel the backing from the adhesive on the rear of the selection button panel.

Align the three tabs on the selection button panel with the three holes on the

LCD screen support.

Once aligned, press firmly on the selection button panel so that it sticks to the

LCD screen support.

Содержание Eccellenza Cafe













































































































Результаты поиска

Содержание Eccellenza Cafe

Отзывы:

Похожие инструкции для Eccellenza Cafe

Бренды по названию

Популярные бренды

VKI Technologies Eccellenza Cafe, Руководство по обслуживанию

Результаты поиска

Содержание Eccellenza Cafe

Отзывы:

Похожие инструкции для Eccellenza Cafe

Бренды по названию

Популярные бренды