VKI Technologies Eccellenza Cafe Скачать руководство пользователя

Страница: 32 / 108

Eccellenza Café – Service Manual

August 5, 2013

Remove the three coffee bean dispensers.

Remove dispenser #1 (left) by lifting the front of the dispenser and pulling it

towards you.

Remove dispenser #3 (right) by lifting the front of the dispenser and pulling it

towards you.

Remove dispenser #2 (center) by lifting the front of the dispenser and pulling

it towards you.
The center dispenser can only be removed only after the other two

dispensers are removed. It must also be installed first when installing

the three dispensers.

To install the replacement coffee bean dispenser, follow these same instructions

in the reverse order.

Содержание Eccellenza Cafe













































































































Результаты поиска

Содержание Eccellenza Cafe

Отзывы:

Похожие инструкции для Eccellenza Cafe

Бренды по названию

Популярные бренды

VKI Technologies Eccellenza Cafe, Руководство по обслуживанию

Результаты поиска

Содержание Eccellenza Cafe

Отзывы:

Похожие инструкции для Eccellenza Cafe

Бренды по названию

Популярные бренды