VKI Technologies Eccellenza Cafe Скачать руководство пользователя

Страница: 4 / 108

Eccellenza Café – Service Manual

August 5, 2013

Table of Contents

Replacing Main Power Components ................................................... 82

Circuit Breakers (5 Amp) .................................................................. 83

Fuse Holder (15 Amp) ...................................................................... 83

Main Power Switch .......................................................................... 83

Service Cord Power Plug .................................................................. 83

Installing the Coin Changer System .................................................. 84

Install the changer housing skirt and levelers ..................................... 84

Install the changer housing .............................................................. 85

Install the coin changer assembly...................................................... 87

Test the machine and the coin changer system ................................... 88

Installing the Bill Acceptor System ................................................... 89

Install the bill acceptor housing skirt and levelers ................................ 89

Install the bill acceptor & changer housing. ........................................ 90

Install the coin changer assembly...................................................... 92

Install the bill acceptor assembly ...................................................... 93

Connect the wiring .......................................................................... 95

Test the machine and the bill acceptor/coin changer system ................. 96

Installing the Printer System ............................................................ 97

Installing the Printer and Housing ..................................................... 97

Printer Buttons ............................................................................... 98

Paper Specifications: ....................................................................... 98

Installing the Printer Paper Roll ......................................................... 99

Automatic Paper Loading ................................................................ 100

Manual Paper Loading .................................................................... 100

Printer Status LED ......................................................................... 101

Machine Messages ......................................................................... 101

Replacing the Printer Module .......................................................... 102

Error Messages ................................................................................ 105

Updating Firmware and Support Files ............................................. 108

Information in this document is subject to change without notice.

Содержание Eccellenza Cafe













































































































Результаты поиска

Содержание Eccellenza Cafe

Отзывы:

Похожие инструкции для Eccellenza Cafe

Бренды по названию

Популярные бренды

VKI Technologies Eccellenza Cafe, Руководство по обслуживанию

Результаты поиска

Содержание Eccellenza Cafe

Отзывы:

Похожие инструкции для Eccellenza Cafe

Бренды по названию

Популярные бренды