VKI Technologies Eccellenza Cafe Скачать руководство пользователя

Страница: 79 / 108

Eccellenza Café – Service Manual

August 5, 2013

Replacing the Exhaust Fan

With the power to the machine switched off, remove the machine’s top cover and

then the left side panel.

At the rear of the machine, remove the fan cover (and screen) from the exhaust fan.

The cover is clipped onto the outside of the exhaust fan and can be easily pried off

by hand. If it cannot be removed by hand, a flat head screwdriver can be used to

gently pry it off.

The fan is secured to the rear wall of the machine with four screws and hex nuts.

Remove the four screws using a screwdriver while holding their respective hex nuts

with a nut driver or small wrench. Be careful not to lose the lock washers for each

hex nut.

Содержание Eccellenza Cafe













































































































Результаты поиска

Содержание Eccellenza Cafe

Отзывы:

Похожие инструкции для Eccellenza Cafe

Бренды по названию

Популярные бренды

VKI Technologies Eccellenza Cafe, Руководство по обслуживанию

Результаты поиска

Содержание Eccellenza Cafe

Отзывы:

Похожие инструкции для Eccellenza Cafe

Бренды по названию

Популярные бренды