Villa Rotograph EVO Скачать руководство пользователя страница 70

Страница: 70 / 223

SERVICE MANUAL

Installation

(Rev. 1)

Rotograph EVO

6-11

Remove the column rotation fixing screw, located in the back side of
the column basement and loose the upper fixing bracket "F" (Figure

6-3) removing the two screws in column side and the two in wall side
and loosening the two central screws. Rotate the upper fixing bracket

"F".

Rotate the column in clockwise direction in order to reach the
column back side.

Lift the Ceph arm with the red handle and the handling zone and
remove it from the package (Figure 6-10).

Position the Ceph arm near the column and using the reference pins
and screws, fix the Ceph arm to the column (Figure 6-11).

Insert the cable in the hole between column and rotating arm and

connect it to the relevant connector on the CPU board.

Remove the red handle.

Reference pin

Figure 6-11

Содержание Rotograph EVO
































































































































































































































Результаты поиска

Содержание Rotograph EVO

Отзывы:

Бренды по названию

Популярные бренды

Villa Rotograph EVO, Руководство по обслуживанию

Результаты поиска

Содержание Rotograph EVO

Отзывы:

Бренды по названию

Популярные бренды