Villa Rotograph EVO Скачать руководство пользователя страница 24

Страница: 24 / 223

SERVICE MANUAL

Description

(Rev. 1)

Rotograph EVO

3-5

3.2.1.

Film / Screen combinations

To get a good image quality, it is advisable to match the intensifying
screens and the films, as indicated hereafter:

Films

Sensibility

Screen

KONICA MG

Green

KIRAN Green 400

KONICA MGH

Green

KIRAN Green 400

KODAK

T-MAT G/RA

Green

KODAK

Lanex Regular

AGFA HTA

Green

AGFA Medium

FUJI HR-G

Green

FUJI G8

IMATION XDA

Green

IMATION T 16

KODAK

T-MAT G/RA

Green

KODAK

Lanex Medium

KONIKA MG

Green

KONIKA KR II

KONIKA MGH

Green

KONIKA KR II

STERLING

ULTRAVISION

Blu

STERLING

Ultravision Rapid

Table 1

NOTE:

It is advisable to use always films and screens of the same brand.

Combinations of films and screen of different manufacturer are possible
so long as the same sensitivity is maintained.

Never combine films and

screens with different sensibility (green and blue).

The factory set values of the exposure factors listed in paragraph 7.4.1 as
default, are indicative and optimised for the combination film/screen

supplied with the device (film T-MAT G/RA and screens Lanex Regular or
film KONIKA MG and KIRAN screens). For the other combinations listed

in the table or for further combinations, the exposure factors have to be
modified accordingly by acting as described in paragraph 7.4.
The real adjustment of these values depends on different conditions,

such as the preference of the user for very/little exposed images.
The quality of the image, therefore, does not exclusively depend on the

device, but it is also extremely important to pay attention to the
processing procedure of the films and the materials related.

NOTE:

Perform the maintenance of the film processor as described in the related
instruction manual.

Regularly check the levels of the used chemical substances; replace them
regularly as indicated by the manufacturer (or according to the number

of processed films).

Содержание Rotograph EVO
































































































































































































































Результаты поиска

Содержание Rotograph EVO

Отзывы:

Бренды по названию

Популярные бренды

Villa Rotograph EVO, Руководство по обслуживанию

Результаты поиска

Содержание Rotograph EVO

Отзывы:

Бренды по названию

Популярные бренды