manualshive.com logo in svg

VESPA 633844 IT, Руководство по обслуживанию, Страница: 265 / 308

Поделиться
Скачать
VESPA 633844 IT Скачать руководство пользователя страница 265

•Instrument panel lights

• Horn

• electric start up

• Engine stopping with emergency stop switch

• electric saddle opening button

CAUTION

TO ENSURE MAXIMUM PERFORMANCE, THE BATTERY MUST BE CHARGED BEFORE USE.
INADEQUATE CHARGING OF THE BATTERY WITH A LOW LEVEL OF ELECTROLYTE BEFORE
IT IS FIRST USED SHORTENS THE LIFE OF THE BATTERY.

CAUTION

WHEN INSTALLING THE BATTERY, ATTACH THE POSITIVE LEAD FIRST AND THEN THE NEG-
ATIVE LEAD.

WARNING

BATTERY ELECTROLYTE IS TOXIC AND IT MAY CAUSE SERIOUS BURNS. IT CONTAINS SUL-
PHURIC ACID. AVOID CONTACT WITH EYES, SKIN AND CLOTHING.
IN CASE OF CONTACT WITH EYES OR SKIN, RINSE WITH ABUNDANT WATER FOR ABOUT 15
MINUTES AND SEEK MEDICAL ATTENTION AT ONCE.
IF IT IS SWALLOWED, IMMEDIATELY DRINK LARGE QUANTITIES OF WATER OR VEGETABLE
OIL. SEEK IMMEDIATE MEDICAL ATTENTION.
THE BATTERIES PRODUCE EXPLOSIVE GAS; KEEP THEM AWAY FROM NAKED FLAMES,
SPARKS AND CIGARETTES. IF THE BATTERY IS CHARGED IN A CLOSED PLACE, TAKE CARE
TO ENSURE ADEQUATE VENTILATION. ALWAYS PROTECT YOUR EYES WHEN WORKING
CLOSE TO BATTERIES.
KEEP OUT OF THE REACH OF CHILDREN

CAUTION

NEVER USE FUSES WITH A CAPACITY HIGHER THAN THE RECOMMENDED CAPACITY. USING
A FUSE OF UNSUITABLE RATING MAY SERIOUSLY DAMAGE THE VEHICLE OR EVEN CAUSE
A FIRE.

Levels check

Level check:

- Hydraulic brake system liquid level.

- Rear hub oil level

- Engine coolant level

- Engine oil level

Road test

Test ride

- Cold start

- Instrument operations

- Response to the throttle control

- Stability on acceleration and braking

- Rear and front brake efficiency

- Rear and front suspension efficiency

Vespa GTV 250 i.e.

Pre-delivery

PRE DE - 3

Содержание 633844 IT





















































































































































































































































































































Отзывы:

Нет отзывов