VESPA 633844 IT Скачать руководство пользователя страница 134

Страница: 134 / 308

Inspecting the valve sealings

- Insert the valves into the cylinder head.

- Alternatively check the intake and exhaust

valves.

- The test is carried out by filling the manifold with

petrol and checking that the head does not ooze

through the valves when these are just pressed

with the fingers.

Inspecting the valve housings

- Check the width of the imprint on the valve

seat«

» wear limit max. 1.6 mm.

- Remove any carbon formation from the valve

guides.

- Measure the inside diameter of each valve guide.

- Take the measurement at three different heights

in the rocker arm push direction.

- If the width of the impression on the valve seat or

the diameter of the valve guide exceed the speci-

fied limits, replace the cylinder head.

Characteristic

Valve seat wear Intake guide

limit accepted: 5.022

Valve seat wear Intake guide

Standard diameter: 5.000 ÷ 5.012 mm

Valve seat wear Exhaust guide

Accepted limit 5.022

Valve seat wear Exhaust guide

Standard diameter: 5.000 ÷ 5.012 mm

Engine

Vespa GTV 250 i.e.

ENG - 40

Содержание 633844 IT





















































































































































































































































































































Результаты поиска

Содержание 633844 IT

Отзывы:

Бренды по названию

Популярные бренды

VESPA 633844 IT, Руководство по обслуживанию

Результаты поиска

Содержание 633844 IT

Отзывы:

Бренды по названию

Популярные бренды