VESPA 633844 IT страница 192 Скачать руководство пользователя

Страница: 192 / 308

Specification

Desc./Quantity

Fuel injector

Lambda sensor

Electric fan starter

The ignition system is integrated with the injection and is of the inductive high efficiency type.

The control unit manages two important parameters:

- Ignition advance

This is optimised according to the engine rpm, to the engine load, temperature and ambient pressure

With idle engine, it is optimised to obtain the stabilisation of the speed at 1450 ± 50 R/1'.

- Magnetisation time

The coil magnetisation time is controlled by the control unit. The ignition power is increased during the

engine start-up.

The injection system recognises the 4-stroke cycle and therefore, ignition is only controlled during

compression.

Specific tooling

020331Y

Digital multimeter

Check that the injection load 10A fuse No. 3 is in

good conditions.

Check that the 7.5A fuse No. 2 for the live control

unit is in good conditions.

Check there is voltage between pins 22 and 26 of

the interface wiring for around two seconds when

switching to «

».

Injection

Vespa GTV 250 i.e.

INJEC - 32

Содержание 633844 IT





















































































































































































































































































































Результаты поиска

Содержание 633844 IT

Отзывы:

Похожие инструкции для 633844 IT

Бренды по названию

Популярные бренды

VESPA 633844 IT, Руководство по обслуживанию

Результаты поиска

Содержание 633844 IT

Отзывы:

Похожие инструкции для 633844 IT

Бренды по названию

Популярные бренды