VESPA 633844 IT страница 154 Скачать руководство пользователя

Страница: 154 / 308

Oil pressure check

- Remove the electrical minimum oil pressure

switch connection and remove the switch.

- Check the oil pressure reading is between 0.5

and 1.2 atm with the engine idling at 1650 rpm and

the oil at the required temperature (wait for at least

one electric ventilation).

- Check the oil pressure is between 3.2 and 4.2

atm with the engine running at a speed 6000 rpm

and the oil at the required temperature.

- Remove the appropriate tools once the meas-

urement is complete, refit the oil pressure switch

and washer, tightening it to the specified torque

and fit the fan cover.

- If the oil pressure is outside the specified limits,

in the following order, check: the oil filter, the oil

by-pass valve, the oil pump and the crankshaft

seals.

N.B.

THE CHECK MUST BE CARRIED OUT WITH
OIL AT THE CORRECT LEVEL AND WITH AN
OIL FILTER IN GOOD CONDITION.

Characteristic

Oil pressure

Minimum pressure admitted at 6000 rpm: 3.2 atm.

Locking torques (N*m)

Minimum oil pressure sensor

12 ÷ 14

Crankshaft oil seals

Engine

Vespa GTV 250 i.e.

ENG - 60

Содержание 633844 IT





















































































































































































































































































































Результаты поиска

Содержание 633844 IT

Отзывы:

Похожие инструкции для 633844 IT

Бренды по названию

Популярные бренды

VESPA 633844 IT, Руководство по обслуживанию

Результаты поиска

Содержание 633844 IT

Отзывы:

Похожие инструкции для 633844 IT

Бренды по названию

Популярные бренды