VESPA 633844 IT Скачать руководство пользователя страница 107

Страница: 107 / 308

Drive-belt

- Check that the driving belt is not damaged.

- Check the width of the belt.

Characteristic

250 4T Transmission belt/minimum width

19.5 mm

250 4T Transmission belt/standard width

21.3 ± 0.2 mm

During the wear checks in the scheduled servicing

programme, you are advised to check the rim bot-

tom of the toothing does not show signs of inci-

sions or cracking (see figure): The rim bottom of

the tooth must not have incisions or cracking; if it

does, change the belt.

Removing the driving pulley

- Turn the crankshaft until the ropes of the pulley

are on a horizontal axis

- Insert the adaptor sleeve of the appropriate tool

in the hole shown in the photograph

Vespa GTV 250 i.e.

Engine

ENG - 13

Содержание 633844 IT





















































































































































































































































































































Результаты поиска

Содержание 633844 IT

Отзывы:

VESPA 633844 IT, Руководство по обслуживанию, Страница: 107 / 308

Результаты поиска

Содержание 633844 IT

Отзывы: