VESPA 633844 IT страница 77 Скачать руководство пользователя

Страница: 77 / 308

Diagnostic code - 2 flashes

Two-flash code shows a system where the control

unit does not show the transponder signal. This

might depend on the inefficiency of the immobiliser

aerial or the transponder.

Turn the switch to ON using several keys: if the

code is repeated even with the Master key, check

the aerial wiring and change it if necessary. If this

is not the case, replace the defective key and/or

reprogram the control unit. Replace the control unit

if the problem continues.

Diagnostic code - 3 flashes

The three-flash code indicates a system where the

control unit does not recognise the key. Turn the

switch to ON using several keys: if the error code

is repeated even with the Master key, replace the

control unit. If this is not the case, perform a re-

programming.

Battery recharge circuit

The recharge system is provided with a three-phase alternator with permanent magneto flywheel.

The alternator is directly connected to the voltage regulator.

This, in its turn, is connected directly to the ground and the battery positive terminal passing through

the 30A protective fuse.

The three- phase generator provides good recharge power and at low revs, a good compromise is

achieved between generated power and idle stability.

Stator check

Stator winding check-up

WARNING

THE CHECK-UP CAN BE MADE WITH THE STATOR PROPERLY INSTALLED.

1) Lift the saddle and remove the helmet compartment.

2) Disconnect the connector between stator and regulator with the three yellow cables as shown in the

photograph.

3) Measure the resistance between each of the yellow terminals and the other two.

Vespa GTV 250 i.e.

Electrical system

ELE SYS - 25

Содержание 633844 IT





















































































































































































































































































































Результаты поиска

Содержание 633844 IT

Отзывы:

Похожие инструкции для 633844 IT

Бренды по названию

Популярные бренды

VESPA 633844 IT, Руководство по обслуживанию

Результаты поиска

Содержание 633844 IT

Отзывы:

Похожие инструкции для 633844 IT

Бренды по названию

Популярные бренды