VESPA 633844 IT страница 126 Скачать руководство пользователя

Страница: 126 / 308

MOVING THE CHAIN AND THE DRIVING
SHAFT CHAIN TIGHTENER.

Removing the valves

- Using the appropriate tool fitted with an adaptor,

remove the cotters, caps, springs and valves.

- Remove the oil guards with the appropriate tool.

- Remove the lower spring supports.

CAUTION

REPLACE THE VALVES IN SUCH A WAY AS
TO RECOGNISE THEIR ORIGINAL POSITION
ON THE HEAD.

Specific tooling

020382Y011

adapter for valve removal tool

020382Y

Valve cotters equipped with part 012

removal tool

020431Y

Valve oil seal extractor

Removing the cylinder - piston assy.

Removing cylinder and piston

- Remove the chain guide pad.

- Remove the 4 O-rings on the stud bolts.

- Pull out the cylinder.

- Remove the cylinder base gasket.

- Remove the two stop rings, the wrist pin and the

piston.

- Remove the piston seals.

CAUTION

TO AVOID DAMAGING THE PISTON, SUP-
PORT IT WHILE REMOVING THE CYLINDER.

N.B.

BE CAREFUL NOT TO DAMAGE THE SEALING
RINGS DURING REMOVAL.

Engine

Vespa GTV 250 i.e.

ENG - 32

Содержание 633844 IT





















































































































































































































































































































Результаты поиска

Содержание 633844 IT

Отзывы:

Похожие инструкции для 633844 IT

Бренды по названию

Популярные бренды

VESPA 633844 IT, Руководство по обслуживанию

Результаты поиска

Содержание 633844 IT

Отзывы:

Похожие инструкции для 633844 IT

Бренды по названию

Популярные бренды