VESPA 633844 IT Скачать руководство пользователя страница 237

Страница: 237 / 308

Refitting

- Carry out the operations in the reverse order from

the removal being careful to respect the direction

of disc rotation shown by the arrow printed on it

- Tighten the six screws to the specified torque.

Locking torques (N*m)

Brake disc screws:

6 +0.5 -1 Nm

Disc Inspection

- Remove the front wheel

- Use a micrometer to check the disc thickness as

shown in the photograph

- Repeat the measurement in at least 6 points on

the disk

- Remove the front brake calliper

- In order to secure the appropriate tool adequately

use a metal plate with M8 threaded hole and fix it

to one of the two front brake calliper attachment

points

- Place the dial gauge on the disk outer edge

- Make the wheel hub turn and check the disk de-

viation

Specific tooling

020335Y

Magnetic support for dial gauge

Characteristic

Standard thickness:

4 +0.2-0.2 mm

Max. deviation allowed:

0.1 mm

Front brake pads

Vespa GTV 250 i.e.

Braking system

BRAK SYS - 9

Содержание 633844 IT





















































































































































































































































































































Результаты поиска

Содержание 633844 IT

Отзывы:

VESPA 633844 IT, Руководство по обслуживанию, Страница: 237 / 308

Результаты поиска

Содержание 633844 IT

Отзывы: