VESPA 633844 IT страница 150 Скачать руководство пользователя

Страница: 150 / 308

Refitting the crankcase halves

- Fit the internal bulkhead by locking the two

screws to the prescribed torque.

- Fit the oil filter fitting and tighten it to the specified

torque.

- Position the oil pre-filter element as shown in the

photograph.

- Place a new gasket on one of the crankcase

halves, preferably on the transmission side, to-

gether with the locating dowels.

- Lubricate the main bushings and insert the crank-

shaft in the transmission side crankcase half.

- Reassemble the two crankcase halves.

- Fit the 10 screws and tighten them to the pre-

scribed torque.

- Fit a new O-ring on the pre-filter and lubricate it.

- Insert the filter on the engine with the relative cap.

Tighten to the prescribed torque.

Locking torques (N*m)

Internal engine crankcase bulkhead (transmis-
sion-side half shaft) screws

4 ÷ 6

Engine-

crankcase coupling screws

11 ÷ 13

Oil filter on

crankcase fitting

27 ÷ 33

Engine oil drainage

plug/mesh filter

24 ÷ 30

Engine

Vespa GTV 250 i.e.

ENG - 56

Содержание 633844 IT





















































































































































































































































































































Результаты поиска

Содержание 633844 IT

Отзывы:

Похожие инструкции для 633844 IT

Бренды по названию

Популярные бренды

VESPA 633844 IT, Руководство по обслуживанию

Результаты поиска

Содержание 633844 IT

Отзывы:

Похожие инструкции для 633844 IT

Бренды по названию

Популярные бренды