VESPA 633844 IT Скачать руководство пользователя страница 146

Страница: 146 / 308

N.B.

THE MAIN BEARINGS ARE NOT GRINDABLE

Specific tooling

020074Y

Support base for checking crankshaft

alignment

Characteristic

Off-line maximum admitted

= 0.15 mm

= 0.01 mm

= 0.10 mm

Inspecting the crankcase halves

- Before proceeding to check the crankcase

halves, thoroughly clean the all surfaces and oil

ducts.

- On the transmission-side crankcase half, take

particular care when handling the oil pump com-

partment and the oil ducts, the by-pass duct, the

main bushings and the cooling jet on the trans-

mission side (see diagram).

- Take particular care, also, that there are no signs

wear in the oil by-pass valve housing (see Chapter

Lubrication), as this could prevent a good seal in

the valve, which regulates the oil pressure.

- On the flywheel side crankcase half, take partic-

ular care cleaning the oil ducts for the main bush-

ings, the oil duct for the jet that lubricates the

cylinder head and the oil drainage duct at the fly-

wheel side oil seal.

- Inspect the coupling surfaces on the crankcase

halves for scratches or deformation, taking partic-

ular care with the cylinder/crankcase surfaces and

the crankcase halves surfaces.

- Defects in the crankcase coupling gasket be-

tween the crankcase halves or the mating surfaces

shown in the diagram, could cause a drop in the

oil pressure lubricating the main bearings and con-

nection rod.

Engine

Vespa GTV 250 i.e.

ENG - 52

Содержание 633844 IT





















































































































































































































































































































Результаты поиска

Содержание 633844 IT

Отзывы:

VESPA 633844 IT, Руководство по обслуживанию, Страница: 146 / 308

Результаты поиска

Содержание 633844 IT

Отзывы: