VESPA 633844 IT Скачать руководство пользователя страница 158

Страница: 158 / 308

Measure the distance between the outer rotor and

the pump body (see figure).

- Check the axial clearance of the rotors using a

trued bar as shown in the figure.

Characteristic

Axial rotor clearance

Limit values admitted: 0.09 mm

Distance between the outer rotor and the pump
body

Admissible limit clearance: 0.20 mm

Distance between the rotors

Admissible limit clearance: 0.12 mm

Refitting

- Check there are no signs of wear on the oil pump

shaft or body.

- Check there are no signs of scoring or wear on

the oil pump cover.

- If you detect non-conforming measurements or

scoring, replace the faulty parts or the unit.

- Fit the pump cover in the position that permits the

crankcase fixing screws to be aligned.

- Make sure the gasket is positioned properly and

refit the pump on the engine crankcase. The pump

can only be fitted in one position. - Tighten the

screws to the prescribed torque.

Engine

Vespa GTV 250 i.e.

ENG - 64

Содержание 633844 IT





















































































































































































































































































































Результаты поиска

Содержание 633844 IT

Отзывы:

VESPA 633844 IT, Руководство по обслуживанию, Страница: 158 / 308

Результаты поиска

Содержание 633844 IT

Отзывы: