manualshive.com logo in svg

VESPA 633844 IT, Руководство по обслуживанию


Поделиться
Скачать
background image

1. Place the vehicle on its centre stand and on flat ground.

2. Undo cap/dipstick "

A

", dry it off with a clean cloth and replace it, 

screwing down completely

.

3. Remove the cap/dipstick again and check that the level is between the min and max. marks; top

up if necessary.

The MAX level mark indicates a quantity of around 1300 cc of engine oil. If the check is carried out after

the vehicle has been used, and therefore with a hot engine, the level line will be lower; in order to carry

out a correct check it is necessary to wait at least 10 minutes after the engine has been stopped, so as

to get the correct level.

Oil top up

The oil should be topped up after having checked

the level and in any case by adding oil 

without

ever exceeding the MAX. level

.

Restoration of the level from 

MIN

 to 

MAX

 requires

approximately 

200 cc

.

Engine oil filter

The cartridge filter must be replaced every time the oil is changed. Use new oil of the recommended

type for topping up and changing purposes.

Make sure the pre-filter and drainage plug O-rings are in good conditions. Lubricate them and refit the

mesh filter and oil drainage plug, screwing them up to the specified torque. Refit the new cartridge filter

being careful to lubricate the O-ring before the fitting. Change the engine oil.

Recommended products

AGIP CITY HI TEC 4T

 

Engine oil

SAE 5W-40 Synthetic oil that exceed the requirements of API SL, ACEA A3, JASO MA specifications

Oil pressure warning light

The vehicle is equipped with a warning light on the instrument panel that lights up when the key is turned

to the «

ON

» position. However, this light should switch off once the engine has been started.

If the light turns on during braking, at idling speed or while turning a corner, it is necessary to

check the oil level and the lubrication system.

Maintenance

Vespa GTV 250 i.e.

MAIN - 10

Содержание 633844 IT





















































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 633844 IT

GLOBBER 505-100 Manual preview
505-100
Бренд: GLOBBER Страницы: 72
Ops-Core Mesh Helmet Cover Installation preview
Mesh Helmet Cover
Бренд: Ops-Core Страницы: 2
KYMCO PEOPLE S 125 Owner'S Manual preview
PEOPLE S 125
Бренд: KYMCO Страницы: 55
Yoshimura RACE 13100CP520 Manual preview
RACE 13100CP520
Бренд: Yoshimura Страницы: 7
Avenger 160 STREET Manual preview
160 STREET
Бренд: Avenger Страницы: 31
Suzuki gsr750 Technical Information preview
gsr750
Бренд: Suzuki Страницы: 44
AMFD RideMaxx Quick Start Manual preview
RideMaxx
Бренд: AMFD Страницы: 17
Crivit 303613 Instructions For Use Manual preview
303613
Бренд: Crivit Страницы: 58
SCA 394021 Owner'S Instruction Manual preview
394021
Бренд: SCA Страницы: 5
Thunderbike Old style Manual preview
Old style
Бренд: Thunderbike Страницы: 7
Yamaha YZ85(Z) Owner'S Manual preview
YZ85(Z)
Бренд: Yamaha Страницы: 86
Yamaha YZ85 2013 Owner'S Manual preview
YZ85 2013
Бренд: Yamaha Страницы: 88
Yamaha TDM850'99 4TX-AE3 Service Manual preview
TDM850'99 4TX-AE3
Бренд: Yamaha Страницы: 43
Yamaha YZFR6Z(C) Owner'S Manual preview
YZFR6Z(C)
Бренд: Yamaha Страницы: 118
Yamaha TT-R125E Owner'S Manual preview
TT-R125E
Бренд: Yamaha Страницы: 92
Yamaha YZF600RT Owner'S Manual preview
YZF600RT
Бренд: Yamaha Страницы: 105
Yamaha YZF-R6T(C) Owner'S Manual preview
YZF-R6T(C)
Бренд: Yamaha Страницы: 111
Yamaha TT-R110E 2018 Owner'S Manual preview
TT-R110E 2018
Бренд: Yamaha Страницы: 88

Бренды по названию

Популярные бренды

Загрузить еще бренды