VESPA 633844 IT страница 235 Скачать руководство пользователя

Страница: 235 / 308

Removal

- Remove the rear brake calliper.

- Remove the brake disc and the hub from the

wheel axle

- To remove the brake disc from the hub, hold the

unit firmly with a vice and operate on the 5 fixing

screws indicated in the photograph

Refitting

- To reassemble the brake disc on the hub, carry out the removal operations in the reverse order ar-

ranging the brake disc on the hub on the side opposite the wheel keying

- Follow the direction of rotation shown by the arrow and tighten to the prescribed torque.

- Fit the hub unit

- disc in the wheel axle

Locking torques (N*m)

Disk to the hub

11 ÷ 13 Nm

Disc Inspection

- Remove the rear brake calliper.

- Check the disc thickness with a micrometer

Characteristic

Minimum thickness allowed after use:

3.5 mm

Standard thickness:

4 +0.2-0.2 mm

- Repeat the measurement at no fewer than six points on the disc.

- Check the regular nature of the rotation of the brake disc assembly using the appropriate tool fixed

onto the brake calliper as shown in the photo.

- In order to be able to anchor the appropriate tool properly use a metal plate with M8 threaded hole

and fix it to one of the two rear brake calliper attachment points.

- Suitably fix the flange to the wheel axle with the original nut and spacer and a Æ 17 mm bearing.

N.B.

SO AS NOT TO GET A DISTORTED READING, CAUSE THE DRIVEN PULLEY SHAFT TO TURN
IN ORDER TO ROTATE THE DISC.

Specific tooling

020335Y

Magnetic support for dial gauge

Vespa GTV 250 i.e.

Braking system

BRAK SYS - 7

Содержание 633844 IT





















































































































































































































































































































Результаты поиска

Содержание 633844 IT

Отзывы:

Похожие инструкции для 633844 IT

Бренды по названию

Популярные бренды

VESPA 633844 IT, Руководство по обслуживанию

Результаты поиска

Содержание 633844 IT

Отзывы:

Похожие инструкции для 633844 IT

Бренды по названию

Популярные бренды