manualshive.com logo in svg

Vertical SBX IP 320, Особенности и руководство по эксплуатации


Поделиться
Скачать
background image

Hunt Groups

84

SBX IP 320 Features & Operation Guide

•

When the number of queued incoming calls are over the pre-defined amount in an ACD 
group, incoming CO calls will be dropped.

•

The Pick-up Hunt Group is reserved for Intercom calls only.

•

ISDN phones can be a member of a Hunt Group, but will only work when answering a 
hunt call.

•

Group pick-up doesn't work with a call of Hunt Group pilot number; an error tone will be 
presented.

•

ISDN phones cannot be the first Hunt Group member; two number entrance for one 
ISDN phone is not permitted.

Admin Programming

•

Hunt Group Assignment (PGM 190)

•

Hunt Group Attribute (PGM 191)

Automatic Call Distribution Groups (ACD Groups)

A separate supervisor or common supervisor can be assigned in an ACD group. The supervisor 
can monitor the status of the group. When a call is queued to a group for longer than a predefined 
time or when a predefined number of calls are queued, the supervisor's LCD will indicate the 
number of calls in queue, and the queued time for the longest queue. The supervisor can change 
the overflow destination and timing. The system will provide traffic and on line status reports, 
based on the supervisor's request for the ACD group, including the following group statistics:

•

Total calls

•

Number of unanswered calls

•

Average and the longest queued calls

•

Number and total time when all agents are busy

•

Average ringing time before answer

•

Average service time after answer

An ACD Supervisor can activate two-way recording when monitoring an agent's conversation.

Queue Information of Queuing Call count is automatically displayed at the Supervisor’s LCD, 
as well as at the Agents’ LCDs. 

Содержание SBX IP 320

























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SBX IP 320

ABRIVO VB-44240A Installation And User Manual preview
VB-44240A
Бренд: ABRIVO Страницы: 24
Radio Shack Cordless Telephone Owner'S Manual preview
Cordless Telephone
Бренд: Radio Shack Страницы: 12
Xorcom XP0020 User Manual preview
XP0020
Бренд: Xorcom Страницы: 9
Panasonic KX-TGD590C Operating Instructions Manual preview
KX-TGD590C
Бренд: Panasonic Страницы: 76
Panasonic KX-TD816JT Features Manual preview
KX-TD816JT
Бренд: Panasonic Страницы: 36
Uniden Extend-A-Phone Operating Manual preview
Extend-A-Phone
Бренд: Uniden Страницы: 51
Radio Shack 43-3906 Owner'S Manual preview
43-3906
Бренд: Radio Shack Страницы: 44
Ameriphone XL-40 Operating Instructions Manual preview
XL-40
Бренд: Ameriphone Страницы: 27
Gigaset C430H Manual preview
C430H
Бренд: Gigaset Страницы: 49
Vodavi Infinite Station User Manual preview
Infinite Station
Бренд: Vodavi Страницы: 38
GreatCall Jitterbug Smart2 Getting Started preview
Jitterbug Smart2
Бренд: GreatCall Страницы: 21
switel D7000 Vita Plus User Manual preview
D7000 Vita Plus
Бренд: switel Страницы: 98
3Com NBX 900-0208 Telephone Manual preview
NBX 900-0208
Бренд: 3Com Страницы: 130
Exibel 36-2947 Manual preview
36-2947
Бренд: Exibel Страницы: 10
NEC MLC Manual preview
MLC
Бренд: NEC Страницы: 18
Aastra 312w User Manual preview
312w
Бренд: Aastra Страницы: 84
Philips XL6601C/23 Quick Start Manual preview
XL6601C/23
Бренд: Philips Страницы: 2
Philips VOIP4331S Specifications preview
VOIP4331S
Бренд: Philips Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды