Vertical SBX IP 320 Скачать руководство пользователя страница 152 | Manualshive

Страница: 152 / 248

background image

Outgoing Call Access

142

SBX IP 320 Features & Operation Guide

Hot Line & Warm Line

A station user can instantly make an outgoing call by lifting the handset or pressing the [ICM],
if the user has previously stored the destination.

The destination can be a CO Line or CO Line Group; the function can be setup on a Flexible
Button, or at another Station.

Hot Line can be activated immediately when the Station is in the off-hook state; Warm Line can
be activated after the Warm Line Timer has expired. If the user dials another number prior to the
Warm Line Timer expiration, the call will activate as a normal call, not as a Warm Line call.

Operation

To activate a Hot Line:

Lift the handset at a station where Hot Line is assigned. The assigned Hot Line feature is
immediately activated.

To activate Warm Line:

Lift the handset at a station where Warm Line is assigned. The assigned Warm Line
feature is activated if no dialing has been done while the Warm Line Timer is running.

Conditions

•

A station can be assigned Hot Line or Warm Line with Admin Programming (PGM 113 -
FLEX 7).

•

If there is no Flexible Button at the station, the number is operated as a Speed Dial
Number.

•

The set value of the Warm Line Timer should be less than that of the Dial Tone Timer.

•

A Flexible Button may be assigned as an Idle Line Selection button.

•

When lifting the handset or pressing the [SPEAKER] button, the system will be activated
as a predefined button if pressed.

•

It is possible to activate Hot Line/Warm Line at an SLT station.

Admin Programming

•

Warm Line Timer (PGM 182 - FLEX 8)

•

Warm Line (PGM 113 - FLEX 7)

•

Idle Line Selection (PGM 122)

«
...
150
151
152
153
154
...
»

Содержание SBX IP 320

























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SBX IP 320

Бренд: Yealink Страницы: 2

Бренд: Dai Telecom Страницы: 21

Бренд: TRIGA Страницы: 33

Бренд: C&TT Страницы: 19

Бренд: Parkside Страницы: 73

Бренд: TATA Motors Страницы: 17

Aegis-09 Series

Бренд: Scitec Страницы: 4

Бренд: Jabra Страницы: 8

AIDE MEMOIRE M7455

Бренд: Aastra Страницы: 2

Бренд: Siemens Страницы: 10

Бренд: Siemens Страницы: 18

Бренд: Siemens Страницы: 2

Gigaset 4010 Comfort

Бренд: Siemens Страницы: 28

Gigaset 3000 Comfort

Бренд: Siemens Страницы: 28

Бренд: Siemens Страницы: 22

Gigaset 4000 Comfort

Бренд: Siemens Страницы: 42

Dualphone DP450

Бренд: Siemens Страницы: 38

Бренд: Siemens Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды