Vertical SBX IP 320 Скачать руководство пользователя страница 88

Страница: 88 / 248

Conference

SBX IP 320 Features & Operation Guide

Admin Programming

•

PGM 160 - FLEX 11: Conference Warning Tone

Paging Conference

During a page by conference page zone, the second originator can page along with the first
originator.

Operation

When a Conference Page is being activated:

Keyset User

Lift the handset and press the [CONF] button.

SLT User

Lift the handset to answer the page.

Hook-flash and dial 58 (conference page join code).

Conditions

•

The Page Timer is not applied to Paging Conference Group.

•

If there is a second page originator, it is impossible to "Meet Me Page."

•

If the first originator goes on-hook, the conference group paging connection is released.

•

The second originator can make paging regardless of page access privilege.

Admin Programming

•

Paging Warning Tone (PGM 161 - FLEX 4)

•

Paging Access (PGM 111 - FLEX 8)

•

Conference Page Zone (PGM 119)

•

Refer to the SBX IP 320 Installation Guide, SLT Conference Page Join Code (PGM 109 -
FLEX 5)

Содержание SBX IP 320

























































































































































































































































Результаты поиска

Содержание SBX IP 320

Отзывы:

Похожие инструкции для SBX IP 320

Бренды по названию

Популярные бренды

Vertical SBX IP 320, Особенности и руководство по эксплуатации

Результаты поиска

Содержание SBX IP 320

Отзывы:

Похожие инструкции для SBX IP 320

Бренды по названию

Популярные бренды