manualshive.com logo in svg

Vertical SBX IP 320, Особенности и руководство по эксплуатации


Поделиться
Скачать
background image

Attendant Service

4

SBX IP 320 Features & Operation Guide

Attendant Forward

The attendant can forward (Unconditional Call Forward) a call to another station. The 
forwarded-to Station will substitute for the attendant temporarily, while the attendant is in the 
forwarded state.

Operation

It is the same procedure as the Unconditional Call Forward.

To activate Attendant Forward:

1.

Lift the Handset or press the [SPEAKER] button.

2.

Press the [DND/FOR] button.

3.

Dial Call Forward Code 1 (Unconditional Call Forward).

4.

Dial Station number.

5.

Hang up the handset and go on-hook.

To deactivate Attendant Forward:

In an idle state, press the [DND/FOR] button.

-or-

In an off-hook state, press the [DND/FOR] button and dial #.

Condition

•

If the attendant assigns unconditional call forward to an SLT or WHTU, the forwarded-to 
station only serves incoming calls as an attendant call or attendant recall. The 
forwarded-to SLT or WHTU cannot activate attendant features.

Содержание SBX IP 320

























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SBX IP 320

NEC Univerge SV9100 User Training preview
Univerge SV9100
Бренд: NEC Страницы: 6
NEC Univerge SV9100 Voicemail Administration Manual preview
Univerge SV9100
Бренд: NEC Страницы: 10
NEC Univerge UM8000 Quick Manual preview
Univerge UM8000
Бренд: NEC Страницы: 7
NEC SL1000 Getting Started Manual preview
SL1000
Бренд: NEC Страницы: 46
NEC SL1000 Technical Training Manual preview
SL1000
Бренд: NEC Страницы: 39
NEC Dterm I Series Quick Reference Manual preview
Dterm I Series
Бренд: NEC Страницы: 5
NEC SL1000 Hardware Manual preview
SL1000
Бренд: NEC Страницы: 150
NEC Univerge SV9100 User Manual preview
Univerge SV9100
Бренд: NEC Страницы: 77
NEC Dterm I Series Owner'S Manual preview
Dterm I Series
Бренд: NEC Страницы: 56
Karel FT10 Technical Reference And User'S Manual preview
FT10
Бренд: Karel Страницы: 72
Aastra Venture IP 480i Installation Manual preview
Venture IP 480i
Бренд: Aastra Страницы: 12
PNI PNI BT27 User Manual preview
PNI BT27
Бренд: PNI Страницы: 2
Doro AUB 300i Manual preview
AUB 300i
Бренд: Doro Страницы: 72
AEI COMMUNICATIONS AFT-4100 Quick Installation Manual preview
AFT-4100
Бренд: AEI COMMUNICATIONS Страницы: 3
Talkaphone VOIP-500E Quick Installation Manual preview
VOIP-500E
Бренд: Talkaphone Страницы: 6
Binatone Lyris 710 User Manual preview
Lyris 710
Бренд: Binatone Страницы: 32
Uniden DECT2080 Series Manuel Du Propriétaire preview
DECT2080 Series
Бренд: Uniden Страницы: 68
A & T International E5812B Quick Start Manual preview
E5812B
Бренд: A & T International Страницы: 6

Бренды по названию

Популярные бренды

Загрузить еще бренды