manualshive.com logo in svg

Vertical SBX IP 320, Особенности и руководство по эксплуатации


Поделиться
Скачать
background image

Voice Service

223

SBX IP 320 Features & Operation Guide

Two-way Recording

Two-way Recording via SMDI

This feature allows a station to record a conversation into the mailbox by pressing a 
{RECORD} button while the station is talking with a CO party.

Operation

To set a {RECORD} flexible button programmed for the Two-way record feature:

1.

Press the [TRANS/PGM] button.

2.

Press the FLEX button (to be assigned).

3.

Press the [TRANS/PGM] button.

4.

Dial 54.

5.

Press the [HOLD/SAVE] button.

While a station user is in a conversation with a CO line caller, the user can press the {RECORD} 
button and the conversation will be recorded in the user's mailbox. The user presses the 
{RECORD} button again or hangs up to end the recording.

Protocol: When the User presses the {RECORD} button, the System sends a SMDI message to 
Voice Mail PC through RS-232C cable. The format is the same as follows.

=>"crlfMD0010mmmmH0xxxxxxxxxbbcrlf^Y"

 cr : carriage return,

 lf : line feed,

 mmmm : VM port number,

 H : Action code for recording,

 xxxxxxxxx : extension which try to record,

 b : ascii space.

Conditions

•

When the recording feature is enabled, the {RECORD} button will flash at 240 ipm. If it 
is disabled, the {RECORD} button will not be lit.

•

The recording feature is not available to SLT.

•

The recording operation is canceled when station goes off-hook, presses the {RECORD} 
button again, presses the [FLASH] button, or the CO party hangs up.

Содержание SBX IP 320

























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SBX IP 320

Radio Shack Cordless Phone Owner'S Manual preview
Cordless Phone
Бренд: Radio Shack Страницы: 12
Uniden DECT2185 Guide Utilisateur preview
DECT2185
Бренд: Uniden Страницы: 40
HTC KAIS100 User Manual preview
KAIS100
Бренд: HTC Страницы: 232
One Talk T41P IP User Manual preview
T41P IP
Бренд: One Talk Страницы: 26
jWIN JT P531 Instruction Manual preview
JT P531
Бренд: jWIN Страницы: 20
Uniden D1779-12BT Manual preview
D1779-12BT
Бренд: Uniden Страницы: 28
Avvio IP-850 User Manual preview
IP-850
Бренд: Avvio Страницы: 62
Splicecom Maximiser Installation And Reference Manual preview
Maximiser
Бренд: Splicecom Страницы: 364
Sanyo TEL-2095 User Manual preview
TEL-2095
Бренд: Sanyo Страницы: 10
Sanyo W32SA Basic Manual preview
W32SA
Бренд: Sanyo Страницы: 112
Sanyo Sprint SCP-5400 User Manual preview
Sprint SCP-5400
Бренд: Sanyo Страницы: 205
Gigaset 120 GE User Manual preview
120 GE
Бренд: Gigaset Страницы: 2
Gigaset Gigaset A380 User Manual preview
Gigaset A380
Бренд: Gigaset Страницы: 16
Gigaset C67H User Manual preview
C67H
Бренд: Gigaset Страницы: 8
Gigaset S510h PRO User Manual preview
S510h PRO
Бренд: Gigaset Страницы: 64
Gigaset E370 Manual preview
E370
Бренд: Gigaset Страницы: 80
Gigaset C300 User Manual preview
C300
Бренд: Gigaset Страницы: 80
Gigaset C575 Manual preview
C575
Бренд: Gigaset Страницы: 88

Бренды по названию

Популярные бренды

Загрузить еще бренды