manualshive.com logo in svg

Vertical SBX IP 320, Особенности и руководство по эксплуатации


Поделиться
Скачать
background image

Internet Protocol (H.450)

123

SBX IP 320 Features & Operation Guide

Net Transfer

Net Transfer is used to transfer net calls. It can transfer any kind of call to a Station in another 
System by pressing the [TRANS/PGM] button and dialing the Station number. The operation 
of net transfer is the same as transferring a call (screened or unscreened) within the same 
System.

Note:  

There are two different kinds of standard net transfer signaling method: transfer by join 

and transfer by rerouting. The main difference is in the connecting path between the 
transferring, transferred, transferred-to Station controls.

•

Join-an additional connecting path is needed to transfer the call to another Station.

•

Routing-a new connecting path is used to transfer the call (the old connecting path of 
transferring station will be cleared).

If both transfer by join and transfer by routing are supported by the System, the appropriate 
mode can be selected using PGM 321.

Operation

Screened Transfer

1.

Press the [TRANS/PGM] button during a conversation. The transferred call will be 
placed on exclusive hold.

2.

Dial the Station number in another Networked System to transfer the call; the 
transferred-to Station of another System will receive a ring signal.

3.

When the transferred-to Station answers, the voice path is connected between the 
transferring and the transferred-to Stations.

4.

Both Stations can talk with one another; the transferred call will remain on hold.

5.

Once the transferred-to Station answers, the transferred call will be connected.

Unscreened Transfer

1.

Press the [TRANS/PGM] button at a Station during a conversation. The transferred call is 
placed on exclusive hold.

2.

The Transferring Station then dials the Station number of another Networked System to 
transfer the call, and goes on-hook.

3.

The transferring station goes idle, and the call will ring at the transferred-to Station in the 
other System.

4.

The transferred caller and the transferred-to Station will be connected when the 
transferred-to Station answers the call.

Содержание SBX IP 320

























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SBX IP 320

Yealink T60 Quick Reference preview
T60
Бренд: Yealink Страницы: 2
3Com VCX V7000 Telephone Manual preview
VCX V7000
Бренд: 3Com Страницы: 118
Roadpost China oneRoam International Cellular User Manual preview
China oneRoam International Cellular
Бренд: Roadpost Страницы: 8
Mac allister MGS1815-Li Manual preview
MGS1815-Li
Бренд: Mac allister Страницы: 47
GE 30542EE1 User Manual preview
30542EE1
Бренд: GE Страницы: 46
BT CALYPSO 120 User Manual preview
CALYPSO 120
Бренд: BT Страницы: 69
Uniden EXP2900 Owner'S Manual preview
EXP2900
Бренд: Uniden Страницы: 28
VoipTel Yealink T28 User Manual preview
Yealink T28
Бренд: VoipTel Страницы: 6
HC Telecom DS815 User Manual preview
DS815
Бренд: HC Telecom Страницы: 16
Panacom PA-7400 User Manual preview
PA-7400
Бренд: Panacom Страницы: 10
JabloCom Essence GDP-06i Quick Start Manual preview
Essence GDP-06i
Бренд: JabloCom Страницы: 8
Uniden DECT2080 Series Manuel Du Propriétaire preview
DECT2080 Series
Бренд: Uniden Страницы: 68
Gigaset Gigaser SL 88 User Manual And Safety Precautions preview
Gigaser SL 88
Бренд: Gigaset Страницы: 74
SoundPeats QY7 User Manual preview
QY7
Бренд: SoundPeats Страницы: 14
GE 2-9896 Use & Care Manual preview
2-9896
Бренд: GE Страницы: 16
GE 21009GE3 User Manual preview
21009GE3
Бренд: GE Страницы: 2
GE 2-9710 Use And Care Manual preview
2-9710
Бренд: GE Страницы: 26
GE 2-9720 Use And Care Manual preview
2-9720
Бренд: GE Страницы: 16

Бренды по названию

Популярные бренды

Загрузить еще бренды