Vertical SBX IP 320 Скачать руководство пользователя

Страница: 43 / 248

Call Handling

SBX IP 320 Features & Operation Guide

To assign the {Camp-On} button as a flexible button:

Press [TRANS/PGM].

Press the FLEX button to be assigned.

Press the [TRANS/ PGM] button.

Type 85.

Press the [HOLD/SAVE] button to save changes.

Conditions

•

During a conference or paging, Call Waiting is not activated.

•

Camp-on is not applied to a station which is in DND mode.

•

The Attendant can override a Station using the Camp-on feature.

•

If the Stop Camp-on Tone (ADMIN program 112 - FLEX 15) is set to ENABLE, the
camp-on tone will not be heard.

Admin Programming

•

Stop Camp-on Tone (PGM 112 - FLEX 15)

•

Voice Over (PGM 113 - FLEX 6): Voice over is also applied to SLT.

Change Ring Type

The ring tone signal used to notify Stations of an incoming call can be changed in ADMIN
Programming to provide distinctive ringing on a per CO line basis. A distinctive ring tone can
be programmed for each CO line that is used to ring each Station.

Admin Programming

•

CO Distinct Ring (PGM 142 - FLEX 5)

•

Ring Frequency (PGM 422)

Содержание SBX IP 320

























































































































































































































































Результаты поиска

Содержание SBX IP 320

Отзывы:

Похожие инструкции для SBX IP 320

Бренды по названию

Популярные бренды

Vertical SBX IP 320, Особенности и руководство по эксплуатации

Результаты поиска

Содержание SBX IP 320

Отзывы:

Похожие инструкции для SBX IP 320

Бренды по названию

Популярные бренды