Vertical SBX IP 320 Скачать руководство пользователя страница 234

Страница: 234 / 248

Voice Service

224

SBX IP 320 Features & Operation Guide

•

This feature is available in the SMDI mode only, not in the DTMF mode.

•

Not available for intercom call recording.

•

If the system has a VMIB, the conversation will be recorded to the VMIB.

•

If Pole 3 of DIP SW1 of MBU is set to OFF (down position) and system has VMIB, the
conversation will be recorded to the VMIU.

Admin Programming

•

Two Way Recording (PGM 112 - FLEX 10)

Two-way Recording via VMIB

This feature allows a station to record a conversation in the mailbox by pressing a {RECORD}
button while the station is talking with a CO party.

Operation

To set a flexible button programmed for 2-way record feature,

Press the [TRANS/PGM] button.

Press the flexible button to be assigned.

Press the [TRANS/PGM] button and dial "54".

Press the [HOLD/SAVE] button.

While a station user is in a conversation with a CO line caller, the user presses the {RECORD}
button and the conversation will be recorded in the user's mailbox. The user presses the
{RECORD} button again or hangs up to end the recording.

Conditions

•

During the recording feature is enabled, the {RECORD} button will flash at 240 ipm and
if it is disabled, the {RECORD} button will be extinguished.

•

Not available to SLT.

•

Recording operation is canceled when station goes off-hook, presses the {RECORD}
button again, presses the [FLASH] button, or the CO party hangs up.

•

Not available for intercom call recording.

•

If the system has an external voice mail system, the conversation will be recorded to the
external voice mail system.

Содержание SBX IP 320

























































































































































































































































Результаты поиска

Содержание SBX IP 320

Отзывы:

Похожие инструкции для SBX IP 320

Бренды по названию

Популярные бренды

Vertical SBX IP 320, Особенности и руководство по эксплуатации

Результаты поиска

Содержание SBX IP 320

Отзывы:

Похожие инструкции для SBX IP 320

Бренды по названию

Популярные бренды